Ninja LPRV2 Startup Manual

NINJA LPRV2 LOW PRESSURE REGULATOR
REASSEMBLY: Reference gure 2
1. Reinsert LPRV2 piston # 9 pin- side first. Be certain the pin enters the center hole (Figure 3: X)
2. Reinsert LPRV2 Main Spring #10, roughly center the spring on the piston.
3. Verify the LPRV2 Adjuster is fully threaded into the LPRV2 Cap, fully turned counterclockwise.
4. Thread, clockwise, the LPRV2 Cap onto the LPRV2 Body NO GAP BETWEEN LPRV2 BODY AND
LPRV2 CAP.
5. Reinstall the LPRV2 Maintenance Access Locking set screw #12, DO NOT OVER TIGHTEN!
6. Re-chronograph using the quick start guide in this manual.
REVISION JANUARY 2018
If you have any ques�ons or require help please call our 877-NINJA-USA (646-5287) for assistance.
186 Virginia Rd, Crystal, Lake, IL 60014 Ph: 877-NINJA-USA (646-5287)
MADE IN USA
Page | 5
START UP GUIDE FOR OPTIMAL PERFORMANCE
-MAXIMUM INPUT PRESSURE OF 500PSI
-SET REFERENCE GAUGE TO 80PSI
-FIRE ROUNDS OVER CHRONOGRAPH
(Pressure may drop)
-INCREASE PRESSURE UNTIL STABLE AND DESIRED
VELOCITY IS ACHIEVED
-ONCE VELOCITY IS STABLE AT DESIRED LEVEL, INSTALL
TOURNAMENT LOCK ZIP TIE IF REQUIRED BY FIELD.
Proudly made in USA
877-NINJA-USA (646-5287) for assistance.
186 Virginia Rd, Crystal, Lake, IL 60014 Ph: 877-NINJA-USA (646-5287)
NINJA LPRV2 NINJA LPRV2 LOW PRESSURE REGULATOR LOW PRESSURE REGULATOR
WARNING: THIS IS NOT A TOY IMPROPER USE CAN RESULT IN INJURY OR DEATH DO NOT USE THE LPR WARNING: THIS IS NOT A TOY IMPROPER USE CAN RESULT IN INJURY OR DEATH DO NOT USE THE LPR
PRIOR TO READING THIS MANUAL IN ITS ENTIRETY PRIOR TO READING THIS MANUAL IN ITS ENTIRETY
The Ninja LPRV2 is a low pressure regulator for Air soft markers. The Ninja LPRV2 is a low pressure regulator for Air soft markers.
Construc�on: Aluminum. Construc�on: Aluminum.
Inlet Pressure: Max 500 PSI Inlet Pressure: Max 1000 PSI
Adjustment Range: 0 -160 PSI Adjustment Range: 0 -160 PSI
Rese�ng Relief Valve: 140-150 PSI, Rese�ng Relief Valve: 140-150 PSI, NOT SERVICEABLE DO NOT REMOVE OR TAMPER WITH. NOT SERVICEABLE DO NOT REMOVE OR TAMPER WITH.
Lubrica�on: Any Silicone based, Lubrica�on: Any Silicone based,
NON-PETROLEUM LUBRICANT. NON-PETROLEUM LUBRICANT.
Adjustment: 3/16" Allen wrench Adjustment: 3/16" Allen wrench
Tournament legal: Can be locked out with zip �e. Tournament legal: Can be locked out with zip �e.
Pressure Gauge: 0-160 PSI Pressure Gauge: 0-160 PSI
Piston: 015-90 red urethane oring for ease of maintenance. Piston: 015-90 red urethane oring for ease of maintenance.
Break In Period: 1000-3000 Cycles Break In Period: 1000-3000 Cycles
Maintenance kit included (Quan�ty (2) of #7 red oring 015 ) Maintenance kit included (Quan�ty (2) of #7 red oring 015 )
The Ninja LPRV2 is designed to be used with a standard regulated paintball air source. The Ninja LPRV2 is designed to be used with a standard regulated paintball air source.
Paintball air source is available in 3000 and 4500 psi bo�les. Paintball air source is available in 3000 and 4500 psi bo�les.
The paintball tank must have a The paintball tank must have a
regulator, which regulates the air source the Max regulator output is regulator, which regulates the air source the optimal regulator output is 500 psi. Ninja o ers a full
line of air systems, visit www.ninjapaintball.com line of air systems, visit www.ninjapaintball.com
Figure 1. Figure 1.
D D
C C
F F
B B A A
Features: Features:
A. Pressure adjustment. A. Pressure adjustment.
B. Tournament Lock zip �e holes. B. Tournament Lock zip �e holes.
C. Maintenance only access lock set screw. C. Maintenance only access lock set screw.
D. Pressure Relief Valve assembly. D. Pressure Relief Valve assembly.
E. Low Pressure Reference Gauge. E. Low Pressure Reference Gauge.
F. Low Pressure Quick Disconnect. F. Low Pressure Quick Disconnect.
If you have any ques�ons or require help please call our 877-NINJA-USA (646-5287) for assistance. If you have any ques�ons or require help please call our 877-NINJA-USA (646-5287) for assistance.
186 Virginia Rd, Crystal, Lake, IL 60014 Ph: 877-NINJA-USA (646-5287) 186 Virginia Rd, Crystal, Lake, IL 60014 Ph: 877-NINJA-USA (646-5287)
MADE IN USA MADE IN USA
Page | 1 Page | 1
500 psi. Ninja o ers a full
E E