Advertisement
Quick Links
Advertisement
Summary of Contents for Perfect-Office A8-W5
- Page 1 Perfect-Office A8 -W5 3DPrinterInstallation Guide...
- Page 2 A8-W5 Assembly Instructions Attention: 1.Please make sure the package not broken when you receive 2.Pleasechecktheprinterpartsaccording tothepackinglist. 3.Please contract your supplier if any questions. 4.The installation of graphics and text for the model diagram, for reference only, in kind to receive goods prevail.
- Page 3 A8 -W5 assembly parts list 1...
- Page 4 A8 -W5 assembly parts list 2...
- Page 5 A8 -W5 assembly parts list 3...
- Page 6 A8 -W5 assembly parts list 4...
- Page 7 A8 -W5 assembly parts list 5...
- Page 8 A8 -W5 assembly parts list 6 Please check printer parts quantity when you receiveit .
- Page 9 Name of each printer part...
-
Page 10: Assembly Step
Assembly Step 1 Please be aware the screw holes is in red circles Step1... - Page 11 Assembly Step 2 Pleasebeawarethescrew holes is in black circles Step 2...
- Page 12 Assembly Step 3 Y axis motor and wire 400mm Motor fixing plate Y axis position switch 700mm Step Rear fixing plate...
- Page 13 Assembly Step 4 Step 2 Step 3...
- Page 14 Assembly Step 5...
- Page 15 Assembly Step 6 Threaded rod 400mm...
- Page 16 Assembly Step 7 Y Guide rod 380mm...
- Page 17 Assembly Step 8 Attention ： Leave vacancy between belt fixation clamp and hot bed fixedplateforbelt positioning.
- Page 18 Assembly Step 9 Before Assembly After Assembly Attention:Please diagonallytighten thescrews when allareinthereplace...
- Page 19 Assembly Step 10 Attention:Belt is for X&Y axis transmitting.Cut the length you need toeach transmission shaft.The belt is 1.5 mintotaland 10-20cm left after installation.
- Page 20 Assembly Step 11 W i n g n u t s w i l l k e e p t h e h e i g h t o f h o t b e d l e v e l a s w e l l a s f i r m i n g t h e h o t b e d . Attention:Hotbed screws should be in the bottom...
- Page 21 Assembly Step 12 Attention: This hole is for Z axis guide rod po sitioning...
- Page 23 Assembly Step 14...
- Page 24 Assembly Step 15 Attention: loose the jackscrew of elastic coupling to place T lead screw tothe bottom,thentighten T lead screw 345mm...
- Page 25 Attention: Please keep A&B at the same level durin g Assembly Step X rods installation. Knock the guide rods with a hammer slightly if it’s hard toplace. X axis Guide rod 436mm After installation tighten the top wire at the back...
- Page 26 Assembly Step 17 Beforedisassembly After disassembly After disassembly Loose M4*6 screws first, thenseparate extruder from L black aluminum parts, rememberto...
- Page 27 Assembly Step 18 Replace M3*20 screws with M3*45 screws M3*45 screwholes...
- Page 28 Assembly Step...
- Page 29 Assembly Step 20 Attention: Install M4*6 screw. Tighten M6 Screw on the throat with spanner till extruder is not loose.
- Page 30 Assembly Step...
- Page 31 Assembly Step 22 M3*20...
- Page 32 AssemblyStep 23 Attention: Belt is for X,Y axis transmitting.The length of belt is 1.5m in total. Normally there’ll be 10-20cm left after installation.
- Page 33 Assembly Step 24 M3 Nut...
- Page 34 Assembly Step...
- Page 35 Assembly Step Attention:This is the wiring diagram of power supply. 1,2,3 seperately represent the line offire(brown),Zero line(blue), ground wire (yellow). 4,5,6 represent negative pole (black) (-);7,8,9represent the positive pole(red)(+).Toavoid danger, please assure the installation is correct .
- Page 36 Assembly Step Redcirclesstandfor thepower screw holes PowerSupply...
- Page 37 Assembly Step 28 Mainboard...
- Page 38 Assembly Step 29 Attention: Please use the corresponding wire , especially motor wire & limited switch wire.
- Page 39 Assembly Step 30 Attention: Please connect the electronics wire to each components correspondingly.
- Page 41 Assembly Step 32 Installation Picture 1...
- Page 42 Assembly Step 32 Installation Picture 2...
-
Page 43: Installation Complete
Installation Complete • Congratulations!Youhavejustmadeyourselfa3D printer ! • Please contact your 3D printer supplier if any puzzlesduringusing process. • Thank you for choosing our products, we will alwaysprovideyoumoreservices.