Advertisement
Quick Links
SAFE BOX HANDLING NOTES – PLEASE READ FIRST
To Open: 1. Depress bottom latch with a slotted screwdriver and lid will pop out. 2. Pull top of lid straight out from
housing without lifting up. 3. Once entirely pulled out, lift lid and it will remain in open position until closed.
To Close: 1. Push lid down without latching bottom. 2. Push in top hinges until it snaps into place. 3. Close bottom until it
latches. 4. Optional screw provided to more permanently secure lid to housing.
Mounting Instructions:
Step 1 – Drill 15/16" hole in desired location in duct.
Step 3 ‐ Insert sensor probe in mounting flange and push until sensor snaps into place. Wire through provided bottom or
side access points. Additional snap‐in conduit adapters available if necessary. Proceed to Configuration Instructions.
Step 1 – Determine wiring location (north side of
building if possible). Drill hole, if necessary, then center
and attach the mounting flange to building.
Step 3 – If wiring through side access points, pierce grommet with knife or remove and snap in conduit adapter.
Additional conduit adapters available if necessary. Proceed to Configuration Instructions.
INSTALLATION INSTRUCTIONS
Step 2 – Align opening in mounting flange with hole in
duct and attach mounting flange to duct using self‐
tapping screws.
Step 2 ‐ If wiring from rear, feed wire from hole into the
rear access point on the sensor. Snap sensor onto
mounting flange.
HUMIDITY SENSORS
Advertisement
Summary of Contents for Tasseron Q-Duct SAFE
- Page 1 HUMIDITY SENSORS INSTALLATION INSTRUCTIONS SAFE BOX HANDLING NOTES – PLEASE READ FIRST To Open: 1. Depress bottom latch with a slotted screwdriver and lid will pop out. 2. Pull top of lid straight out from housing without lifting up. 3. Once entirely pulled out, lift lid and it will remain in open position until closed. To Close: 1. Push lid down without latching bottom. 2. Push in top hinges until it snaps into place. 3. Close bottom until it latches. 4. Optional screw provided to more permanently secure lid to housing. Mounting Instructions: Step 1 – Drill 15/16” hole in desired location in duct. Step 2 – Align opening in mounting flange with hole in duct and attach mounting flange to duct using self‐ tapping screws. Step 3 ‐ Insert sensor probe in mounting flange and push until sensor snaps into place. Wire through provided bottom or side access points. Additional snap‐in conduit adapters available if necessary. Proceed to Configuration Instructions. Step 1 – Determine wiring location (north side of Step 2 ‐ If wiring from rear, feed wire from hole into the building if possible). Drill hole, if necessary, then center rear access point on the sensor. Snap sensor onto and attach the mounting flange to building. mounting flange. ...
- Page 2 Step 3 – Snap on cover. Depress Step 1 – Feed wires through hole in Step 2 ‐ Mount with screws, then rear of sensor. make connections. hooks through vents with tool to remove. Configuration Instructions for ALL Tasseron Humidity Sensors: For optional passive temperature sensor, connect one wire to each quick connect terminal labeled “TEMP” (non‐polar). Instructions for 4 to 20 mA Output DIP Switch Configuration Terminal Function TEMP 2‐pole connection for optional passive temperature sensor (no polarity) VIN Main power – 24V DC power supply recommended 4‐20mA Current mode signal output COM (not used in current mode) VOUT (not used in current mode) Step 1 – Be sure the white Output mode DIP switches are in the proper configuration. For 4‐20mA output, DIP switch #2 must be in the RIGHT position. Switch #1 has no function in this mode. Step 2 – Terminate control wires in quick connects as indicated in the table above. Only 2 wires are needed for 4‐20mA output mode; main power supply and signal output. These wires terminate at “VIN” and “4‐20mA”. ...