Advertisement
GENERAL OPERATION
The KAPTIV-CS-HP-S (Compact Solution High Pressure Stainless Steel) removes all types of
condensate from compressed air systems up to 100 m
The KAPTIV-CS-HP-S is a high pressure, stainless steel zero air loss drain with a pressure rating
from 0 to 50 bar.
The compact robust industrial housing, the 2/2 way direct acting valve, the alarm (NC and NO)
and the integrated mesh strainer make the KAPTIV-CS-HP-S a reliable draining solution.
The alarm function can be connected to any alarm device.
Installation & Maintenance Instructions
KAPTIV-CS-HP-S
Electronically operated level sensed drain
11/12
3
/min. without the loss of compressed air.
1
Advertisement
Table of Contents
Summary of Contents for Jorc KAPTIV-CS-HP-S
- Page 1 100 m /min. without the loss of compressed air. The KAPTIV-CS-HP-S is a high pressure, stainless steel zero air loss drain with a pressure rating from 0 to 50 bar. The compact robust industrial housing, the 2/2 way direct acting valve, the alarm (NC and NO) and the integrated mesh strainer make the KAPTIV-CS-HP-S a reliable draining solution.
-
Page 2: Safety & Warning Instructions
SAFETY INSTRUCTIONS SAFETY AND PROPER USAGE To ensure safe and enduring performance of this product, you must comply strictly with the instructions enclosed herein. Non-compliance with instructions or improper handling of the product will void your warranty! This product is designed to drain condensate from compressed air systems. Usage of this product in conditions not specified in this manual or in contrary to the instructions hereby provided is considered IMPROPER. -
Page 3: Wall-Mounting Bracket
EXPLODED VIEW - IDENTIFY ALL COMPONENTS DIAGRAM Sensor module screw (4x) Connector screw (2x) Sensor plate Screw gasket (2x) Sensor module Sensor module Connector (2x) O-ring small Connector gasket (2x) Sensor module O-ring large Electronics compartment Sensor module (with attached Earth O-ring middle (2x) cable) Housing bolt (4x) -
Page 4: Installation Instructions
3. We strongly recommend to use the wall 4. Use the four mounting screws to secure the mounting bracket to avoid damaging the unit KAPTIV-CS-HP-S to the mounting bracket. by strong vibrations. Fix the mounting bracket against a wall or structure before installing the KAPTIV-CS-HP-S. - Page 5 -We advise to use the outlet nipple delivered with -We advise to use the outlet nipple delivered with the the KAPTIV-CS-HP-S. If it is necessary to use an KAPTIV-CS-HP-S. If it is necessary to use an alternative nipple, make sure it has the correct alternative nipple, make sure it has the correct thread (1/4”BSP), do not over tighten!
-
Page 6: Power Supply
ALARM INSTALLATION INSTRUCTIONS The KAPTIV-CS-HP-S is equipped with an alarm feature. The alarm feature can be connected to an external alarm device with its own power supply. Alarm device ALARM DEVICE POWER SUPPLY Power supply 1. Remove the protection cap from the alarm 2. -
Page 7: Cleaning Instructions
CLEANING INSTRUCTIONS These instructions are for cleaning the KAPTIV-CS-HP-S. If your KAPTIV-CS-HP-S requires maintenance, i.e. replacement of wearing components, please refer to our dedicated maintenance instructions (supplied with the service kit). Depressurise the system before installation or maintenance is carried out! 1. - Page 8 IP65 rating. Make sure the display lights up to check if the power supply is successfully connected. 11. Press and hold down the TEST button 12. Your KAPTIV-CS-HP-S is ready for to check the valve function. operation!
-
Page 9: Service Chart
SERVICE CHART Date Description Name... -
Page 10: Dimensions (Mm)
TECHNICAL SPECIFICATIONS Maximum compressor capacity 100 m /min. Min./max. system pressure 0 bar / 50 bar – 0 psi / 725 psi Valve type 2/2 way, direct acting Valve orifice 1.8 mm – 0.07 inch Valve seals Inlet connection 1/2" (BSP or NPT) Outlet connection 1/4"...