Advertisement
Quick Links
IMPORTANT
Record the serial number from the tag on the back of the safe or
from the tag on the front bottom corner of the safe.
Keep keys and combination in a secure place away from
children. Do not store trouble key or this document in the safe.
Do not move this safe using its handle. The handle should only
be used for opening and closing the door of the safe.
Removing the back panel on the door will void the fire rating.
Serial #:
INSTALLATION OF SCOPE STAND-OFF
NOTE: The scope stand-off will function properly for many
combinations of guns with scopes.
Screw the scope stand-off into the pilot hole of the barrel
rest. (Figure 1)
HANDLE ASSEMBLY
Screw the 5 handle spokes into the hub and hand tighten. (Figure 2).
These spokes are located in the front foam packaging.
NOTE: Do not use this handle to move the safe.
SELECTING A LOCATION
Your safe should be installed in an isolated, dry and secure area.
For extra humidity control we recommend the use of a desiccant. Do not drill
holes in the safe for electrical dehumidifying devices. Do not drill through the
insulation in the rear vent holes. Do not mount the safe to a wall using these
vent hole. This will void the fire rating.
For greater security the safe should be located in a corner and fastened to the
floor. (Figure 3)
SECURING THE SAFE
IMPORTANT: Because this safe is waterproof it will float. As the water level rises, the safe will begin to float and could fall
over causing personal injury.
The safe must be fastened to the floor using the lag bolts and gasket washer provided with this safe to insure the
waterproof rating. Failure to do so will void the waterprooof rating.
You must remove the safe from the skid and place the safe on the floor. Failure to do so will void the fire and
waterproof ratings.
Place the safe in the desired location. Lift the carpeting up and locate the mounting hole bushings. These bushings are filled with
fire resistant caulking which must be drilled out before mounting the safe to the floor. Use a 3/8" diameter drill bit to drill out this
caulking. Continue to use this drill to mark the hole location on the floor. Move the safe away. Drill pilot holes in the floor as follows:
For a wood floor drill 5/16" diameter x 2-1/2" deep pilot holes. For a masonry floor drill 7/16" diameter x 2-1/2" deep pilot holes for
the anchors.
IMPORTANT: When you drill out the fire resistant caulking from the mounting hole bushings you must mount the safe to
the floor using the lag bolts and gasket washers. Failure to do so will void the fire rating and waterproof rating.
Reposition the safe and secure the safe with the lag bolts and gasket washers. (Figure 4) Replace the carpeting.
MODELS WITH OPTIONAL SHELVING
The shelving can be installed by locating the shelf clips to the desired locations and setting the shelf in place.
Do not store electronic media, computer disks, audio-visual media or photographic negatives in this safe.
This material will not survive the rated internal temperature of the safe. This material may be damaged or
destroyed.
WARNING
Key #:
1
Tip Over Hazard
A child or adult can tip the safe
and be killed or seriously injured.
Failure to secure the safe as
shown in these instructions can
result in death or serious injury
to children and adults.
Children should not play with or
around the safe.
Your Electronic Safe Combination:
4
2
40139-0905
3
1
4
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for Field & Stream Pro Series
- Page 1 IMPORTANT WARNING Tip Over Hazard Record the serial number from the tag on the back of the safe or A child or adult can tip the safe from the tag on the front bottom corner of the safe. and be killed or seriously injured. Keep keys and combination in a secure place away from Failure to secure the safe as children.
- Page 2 ELECTRONIC LOCK You must first install the battery which is located in the front protective styrofoam (See BATTERY REPLACEMANT below) 1, 5, 9, # To open an electronic lock the first time, press the following numbers/symbols on the electronic keypad in this order: .
- Page 3 Safe Replacement Key Request - This is not a Registration Form Verification of ownership is required in order to receive your replacement key for your safe In order to receive a replacement key to your security product: Complete the following form and send to Stack-On Products. Send a copy of your valid driver’s license along with the form.
- Page 4 Limited Lifetime Guarantee If your Field & Stream Pro Series Safe suffers damage due to theft or fire at any time while still owned by the original owner, Stack-On will either repair or replace (at Stack-On’s discretion) your safe free of charge. If Stack-On chooses to repair the safe, such work may be performed by a local technician approved by Stack-On.
Need help?
Do you have a question about the Pro Series and is the answer not in the manual?
Questions and answers
What if your safe quits working.
If a Field & Stream Pro Series safe stops working, check the battery first and replace it if necessary. Always hold the battery connecting cap when disconnecting or attaching the battery to avoid damaging the power supply. If the problem is due to a defect in materials or workmanship and the safe is within the five-year warranty period, contact Stack-On’s customer service for assistance. Unauthorized repair or tampering will void the warranty.
This answer is automatically generated
The batteries for the key pad have died and I cannot find the key. How do I get a replacement key. Gun Safe
To get a replacement key for the Field & Stream Pro Series gun safe, you need to request the service and pay a $10.00 charge. You may need to provide your email address and other required details.
This answer is automatically generated
How to remove the door from the safe?
I have the combination to my Field & Stream safe but forgot sequence for the dial.