Using the 1/4" TRS INPUT 1s a "Thru" Connector
Because the XLR connector and the 1/4" TRS
connector are in parallel, you can use the 1/4" TRS
jack as a "Thru" connector to pass the input signal on
to another amplifier's input (see Figure below).
FROM MIXING CONSOLE
LEFT AND RIGHT MAIN OUT
Using the 1/4" TRS INPUT 1s a "Thru" Connector
In MONO and BRIDGE modes,
LOOK
INPUT 1 and INPUT 2 are
connected together in parallel.
This allows you to use INPUT 2 as a
CLOSER
"Thru" connector to daisy-chain the
input signal to another amplifier.
Output Wiring
Use heavy gauge, stranded wire for connecting
speakers to the Speakon outputs jacks. As the
distance between the amplifier and the speakers
increases, the thickness of the wire should also
increase. Speaker wire has resistance, and when
electricity passes through a resistor, power is lost. The
thicker the wire, the less resistance it offers, and the
more power actually gets to the speaker.
The thickness of the wire is rated in gauges. Use the
chart at the right to determine the correct gauge of
wire to use according to the distance between the
speakers and the amplifier, and the impedance of
the load the amplifier is driving. This ensures that the
power lost across the speaker wire is less than 0.5 dB.
INPUT 2
INPUT
CONNECTION
LINE
(BALANCED)
AMP MODE
AMP MODE
INPUT 1
MONO
STEREO
STEREO
LINE
(BALANCED)
AMP MODE SWITCH
STEREO
INPUT 2
INPUT
CONNECTION
LINE
(BALANCED)
INPUT 1
MONO
LINE
(BALANCED)
AMP MODE SWITCH
STEREO
CAUTION
TO REDUCE THE RISK
CHANNEL 2
CHANNEL 2
BRIDGED
BRIDGED
CHANNEL 1
CHANNEL 1
BREAKER
BREAKER
OF FIRE OR ELECTRIC
SHOCK, DO NOT
EXPOSE THIS
APPARATUS TO
RAIN OR MOISTURE.
SEE INSTRUCTIONS
BEFORE USING.
SPEAKER CONNECTION
SPEAKER CONNECTION
CHANNEL 2
BRIDGED
CHANNEL 1
CAUTION
TO REDUCE THE RISK
OF FIRE OR ELECTRIC
SHOCK, DO NOT
EXPOSE THIS
APPARATUS TO
RAIN OR MOISTURE.
SEE INSTRUCTIONS
BEFORE USING.
CHANNEL 2
BRIDGED
CHANNEL 1
Wire Length
Up to 25 ft.
Up to 40 ft.
Up to 60 ft.
Up to 100 ft.
Up to 150 ft.
Up to 250 ft.
Note: If you use an unbalanced
1/4" TS cable to daisy-chain
the TRS input jack to another
amplifier, you will unbalance the
XLR input on the Juice amplifier.
This negates the benefits
associated with balanced lines
and inputs.
DESIGNED IN WOODINVILLE, WA, USA
"TAPCO" IS A REGISTERED TRADEMARK
OF LOUD TECHNOLOGIES INC.
Passive Speakers (Mackie C300s)
DESIGNED IN WOODINVILLE, WA, USA
"TAPCO" IS A REGISTERED TRADEMARK
OF LOUD TECHNOLOGIES INC.
Passive Speakers (Mackie C300s)
Load
Gauge of
Impedance
Wire
2Ω
14 gauge
4Ω
16 gauge
8Ω
18 gauge
2Ω
12 gauge
4Ω
14 gauge
8Ω
18 gauge
2Ω
10 gauge
4Ω
12 gauge
8Ω
16 gauge
2Ω
8 gauge
4Ω
10 gauge
8Ω
14 gauge
2Ω
6 gauge
4Ω
8 gauge
8Ω
12 gauge
2Ω
4 gauge
4Ω
6 gauge
8Ω
10 gauge
11