Advertisement
Quick Links
Advertisement
Related Manuals for Sony HKDW-704
Summary of Contents for Sony HKDW-704
- Page 1 GPS UNIT HKDW-704 INSTALLATION AND MAINTENANCE MANUAL 1st Edition...
- Page 2 Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres. Pour toute réparation faire appel à une personne compétente uniquement. HKDW-704...
- Page 3 In addition to the Installation and Maintenance Manual, the following manuals are available. HKDW-704 Operation Manual (Supplied with HKDW-704) This manual is necessary for application and operation of the HKDW-704. HDW-730/750/750P/750CE Operation Manual (Supplied with HDW-730/750/750P/750CE) MSW-900/900P Operation Manual (Supplied with MSW-900/900P) These manuals are necessary for application and operation of the HDW-730/750/750P/750CE and MSW- 900/900P.
- Page 4 1-2. Confirming Display before Installation and Starting to Use To install the HKDW-704 in the HDW-750/750P/750CE/730 and the MSW-900/900P, the ROM that is installed in the AT-143 board and the SS-92 board must have been upgraded to the versions that support HKDW-704.
- Page 5 This manual is described on the premise of installing the HKDW-704 in the HDW-750/750P/750CE/730. When the HKDW-704 is going to be installed in the MSW-900/900P, substitute the board names of the HDW-750/750P/750CE/730 with the corresponding board names of the MSW-900/900P as shown below.
- Page 6 80 x 10 N.m (8 kgf.cm) Be careful not to pinch the harness between the inside Inside panel Screw assembly panel assembly and the chassis. (with drop-safe) Flexible card wires Hook Screw (with drop-safe) FP-121 board Hinge 1-4 (E) HKDW-704...
- Page 7 For the HDW-750 of serial No.70001 or higher, or when the HKDW-702 is installed, remove the coaxial cable from the connector on the DC-110/110A board. For the MSW-900/900P For the MSW-900/900P, remove the coaxial cable from the connector on the DCP-35 board. 1-5 (E) HKDW-704...
- Page 8 DCP-28 board CN201 Coating lead pin DCP-28 board Distance of TX-78 board 20 mm or more Coaxial cable (white) Harness EQ-88 board Harness AT-143 board Flexible card wire DCP-28 board AT-143 board 1-6 (E) HKDW-704...
- Page 9 Coaxial cable (WHT) 7. Remove the DVP board assembly by slanting it to the front. DVP board assembly Hooks Serial No.10001 through 10119 Serial No.70001 through 70208 Board lever Coaxial cable (WHT) Projections of the SDI shield plate 1-7 (E) HKDW-704...
- Page 10 SS-92 board E portion (CN1) Lock knob Protection assembly cover Opening of Adhesive the frame tape GPS-SS harness Lock lever VF slide assembly Reinstallation Fig.A Reinstall it by reversing the steps of removal. Harness clamp Harness clamp 1-8 (E) HKDW-704...
- Page 11 Harness after the Protection Assembly Cover in the illustration below, and secure it with the harness is already Removed (Tape is not attached to clamp that is supplied with the HKDW-704. the dust protection cover) 1. Remove the four harness clamps.
- Page 12 GPS module in the illustration. Remove the coaxial cable of the CN connector RF cable from the GPS module by raising it straight up. Cover Coaxial cable GPS module Pin-10 Flat head (_) screwdriver 1-10 (E) HKDW-704...
- Page 13 Fig.1 when viewed from the harness top of the handle assembly. When viewed Fig.2 GPS Handle plate from the front CN connector RF cable assembly Square hole Precision Coaxial cable screws P2.6 x 10 1-11 (E) HKDW-704...
- Page 14 3. Bend the four claws of the cover in the direction of the arrow. (Fig.2) Be sure to use long nose pliers to bend the claw of the cover to protect operator from injury due to the sharp edge. 1-12 (E) HKDW-704...
- Page 15 When the GPS F cover is placed, be careful not to pinch the GPS-SS harness between the GPS F cover and the handle assembly. GPS F cover Precision screws P2.6 x 10 W2.6 GPS-SS harness Handle assembly Pin-10 of the GPS module GPS-SS harness 1-13 (E) HKDW-704...
- Page 16 P2 x 4 Connector antenna tapes Exfoliation paper 10. Reinstall the VF slide assembly by reversing the steps Hook (A) of removal. (Refer to step 1 in Section 1-10.) (Hard) GPS antenna tapes Loop (B) (Soft) Exfoliation paper 1-14 (E) HKDW-704...
- Page 17 Therefore, specified parts should be used in the case of replacement. 2. Standardization of Parts Some repair parts supplied by Sony differ from those used for the unit. These are because of parts common- ality and improvement. Parts list has the present standardized repair parts.
- Page 18 1-754-222-11 s ANTENNA, GPS (150) 1-754-223-11 s ANTENNA, GPS (5000) 3-635-653-02 s COVER, F (GPS) 3-691-025-01 o CLAMP, HARNESS 3-694-181-02 s TYPE1, AROCK PRECISION +P2.6X5 1-823-623-11 s CORD, CONNECTION 7-627-557-48 s SCREW, PRECISION +P2.6X10 TYPE1 7-688-002-02 s WASHER (2.6) HKDW-704...
- Page 19 The material contained in this manual consists of information that is the property of Sony Corporation. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation.
- Page 20 Printed in Japan Sony Corporation HKDW-704 (SY) J, E 2003. 2 16 B&P Company 3-206-316-01 (1) ©2003...