Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for GABOR UPM-360
- Page 1 UPM-360 360° UNIVERSAL PROJECTOR MOUNT User Manual...
- Page 2 Thank you for choosing Gabor. The Gabor UPM-360 Universal Projector Mount provides an easy solution for mounting your projector to a flat or slanted ceiling or wall. Preassembled parts make the installation process quick and simple. This mount offers a 1.5 NPT universal attachment which allows for adaptable hardware installations, and 360°...
-
Page 3: Safety Warnings
• It is strongly recommended that this product be installed by a qualified professional or installation contractor; Gabor takes no responsibility for any product damage or personal injury resulting from mishandling, incorrect mounting, faulty assembly, or improper use of this product. - Page 4 Overview Mounting plate Rotating 1.5 NPT column Projector mount Tools Needed for Assembly Wood Concrete M2.5 × 15 mm screw 50 mm anchor screw M6 × 25 mm screw (with washer) (with washer) Stud finder Pencil ...
-
Page 5: Projector Placement
Projector Placement Before installing the Gabor UPM-360, you will need to determine the projector’s placement and identify surrounding ceiling or wall supports for attachment. 1. Measure the width at the top of your projector’s screen, and locate the center. Make a mark above the center point. - Page 6 Wood Studs Wood studs run vertically inside the wall or across the ceiling, behind the drywall or plaster. The plate must be mounted to a wood stud, or the plate could fall out and damage the projector or cause personal harm. Make sure the studs are at least 1.5 inches (38 mm) wide..
- Page 7 Concrete Warning! Make sure anchors are installed into solid concrete that is at least 1.75 inches (44.5 mm) thick. If concrete exhibits cracks or other defects, this may result in failure of the concrete anchors and cause serious personal injury or equipment damage. 1.
- Page 8 Attaching the Projector 1. Determine which screws (M2.5 and M3 (with included washers),M4, M5, or M6) and spacers (3, 4, or 6 mm) to use with your projector. 2. Loosen the projector mount’s arms with a Philips screwdriver. If your projector model has only three holes, then remove the fourth arm with the screwdriver.
-
Page 9: Adjusting The Projector
Adjusting the Projector Caution: Make sure to support the projector with one hand while making Tilt any adjustments. You can adjust the projector’s position up to ±90° tilt, ±25° roll, and 360° rotation. 90° Rotate 360° Roll Note: When mounting to a slanted ceiling or wall, make sure the rotating column’s hooks are facing upward. - Page 10 3. Hang the projector from the rotating column’s hooks and tighten the bolts with the included hex wrench. Using the UPM-360 with Other 1.5 NPT Compatible Mounting Plates Use the UPM-360 with other 1.5 NPT compatible structural mounts or mounting plates such as the Gabor SCP-770 Suspended Ceiling Mount- ing Plate which includes a 1.5 NPT...
-
Page 11: Product Specifications
Product Specifications Maximum load capacity 33 lb. (15 kg) Color Black Tilt ±90° Roll ±25° Rotation 360° Dimensions (H × W × D) 12.4 x 12.4 x 8.8 in. (31.4 x 31.4 x 22.4 cm) Weight 3.25 lb. (1.47 kg) - Page 12 One-Year Limited Warranty This Gabor product is warranted to the original purchaser to be free from defects in materi- als and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later. The warranty provider’s responsibility with respect to this limited warranty shall be limited solely...
Need help?
Do you have a question about the UPM-360 and is the answer not in the manual?
Questions and answers