Advertisement
Table of Contents
- 1 Table of Contents
- 2 IMPORTANT - be Sure to Read this Chapter for Safe Use of the Equipment
- 3 Nomenclature
- 4 Assembly
- 1 Lighting the Illuminator and Adjusting the Light Intensity
- 2 Adjusting the Reflected (Oblique) Illumination Angle
- 3 Adjusting the Focus Adjustment Knob Tension
- Download this manual
This instruction manual is for the Olympus SZ2-ILST LED Illuminator Stand. To ensure the safety,
obtain optimum performance and to familiarize yourself fully with the use of this equipment,
we recommend that you study this manual thoroughly before operating the system.
Retain this instruction manual in an easily accessible place near the work desk for future reference.
INSTRUCTIONS
SZ2-ILST
LED ILLUMINATOR STAND
A X 6 6 1 3
Advertisement
Table of Contents
Summary of Contents for Olympus SZ2-ILST
- Page 1 SZ2-ILST LED ILLUMINATOR STAND This instruction manual is for the Olympus SZ2-ILST LED Illuminator Stand. To ensure the safety, obtain optimum performance and to familiarize yourself fully with the use of this equipment, we recommend that you study this manual thoroughly before operating the system.
- Page 2 For Korea only B급 기기 (가정용 방송통신기자재) 이 기기는 가정용(B급) 전자파적합기기로서 주로 가정에서 사용하는 것을 목적으로 하며, 모든 지역에서 사용할 수 있습니다.
-
Page 3: Table Of Contents
Refer to your local Olympus distributor in the EU for return and/or collection systems available in your country. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. -
Page 4: Important - Be Sure To Read This Chapter For Safe Use Of The Equipment
4. Always use the power cord provided by Olympus. If no power cord is provided, please select the proper power cord by referring to the section “PROPER SELECTION OF THE POWER SUPPLY CORD” at the end of this instruction manual. If the proper power cord is not used, product safety performance cannot be warranted. - Page 5 ” (OFF), unplug the power cord and wipe with a dry cloth. If water penetrates inside the equipment, contact Olympus to have the electrical safety checked. 4. Do not disassemble any part of the equipment as this could result in malfunction or reduced performance.
-
Page 6: Nomenclature
NOMENCLATURE Microscope body mount Reflected light (oblique) LED illuminator (Page 5) Tiltable Microscope body clamping knob Focus adjustment knob (Page 5) Reflected light intensity Power cord connector (Page 4) control knob (Page 5) Transmitted light intensity control knob (Page 5) Accessory mounting holes Main switch (Page 4) “... -
Page 7: Assembly
” (OFF) before connecting the power cord. Always use the power cord provided by Olympus. If no power cord is provided, please select the proper power cord by referring to the section “PROPER SELECTION OF THE POWER SUPPLY CORD” at the end of this instruction manual. -
Page 8: Operation
OPERATION Lighting the Illuminator and Adjusting (Fig. 4) the Light Intensity 1. Press the “ ” (ON) segment of the main switch @ to turn on the LED illuminator. The LED illuminator can be used in both transmitted and reflected light illumination. -
Page 9: Specifications
SZ2-ILST SPECIFICATIONS Item Specifications Applicable microscopes SZ2 series microscopes (SZ51, SZ51-60, SZ61, SZ61-60 or SZ61TR) and SZX7 SZ series microscopes (Previous models) Focus adjustment Focusing stroke 120 mm (85 mm up, 35 mm down) Focus adjustment knob tension is adjustable. -
Page 10: Proper Selection Of The Power Supply Cord
If no power supply cord is provided, please select the proper power supply cord for the equipment by referring to “ Specifications ” and “ Certified Cord ” below: CAUTION: In case you use a non-approved power supply cord for Olympus products, Olympus can no longer warrant the electrical safety of the equipment. - Page 11 SZ2-ILST Table 2 HAR Flexible Cord APPROVAL ORGANIZATIONS AND CORDAGE HARMONIZATION MARKING METHODS Alternative Marking Utilizing Printed or Embossed Harmoniza- Black-Red-Yellow Thread (Length tion Marking (May be located on Approval Organization of color section in mm) jacket or insulation of internal wir-...
- Page 12 Manufactured by Shinjuku Monolith, 2-3-1 Nishi-Shinjuku, Shinjuku-ku, Tokyo 163-0914, Japan Distributed by 48 Woerd Avenue Waltham, MA 02453, U.S.A. 8F Olympus Tower, 446 Bongeunsa-ro, Gangnam-gu, Seoul, Korea 135-509 AX6613 08...