Table of Contents
Advertisement
Quick Links
(2)
sockets.
these
to
connected
be
should
connectors
data
RJ-45
sockets.
RJ-45
shielded
are
ports
Out
Power
&
Data
and
In
Data
Injector
Power
outlet.
particular
that
to
Injector
Power
connect
not
do
voltage,
outlet
power
the
from
different
is
label
the
on
indicated
the
If
hazard.
fire
a
pose
could
and
damage
equipment
cause
can
mismatch
volatge
conductor.
phase
the
on
used
is
international)
(240VAC,
U.S.
3A
VAC,
120
than
larger
no
breaker
circuit
or
fuse
a
Ensure
protection.
current)
(over
short-circuit
for
installation
building
the
on
on
relies
product
source.
its
to
Injector
Power
the
connecting
whenever
measures
safety
electricity
basic
source.
a
to
Injector
Power
the
connecting
before
instructions
installation
the
equipment.
other
on
interfaces
SELV
to
connected
be
only
can
interfaces
These
60950.
IEC
to
to
according
circuits
Voltage)
Extra-Low
(Safety
SELV
as
qualified
are
interfaces
Power
&
Data
and
Data
Injector
Power
accessible.
easily
and
Injector
Power
the
near
be
must
outlet
wall-socket
(0.75mm²)].
18AWG
of
gauge
wire
minimum
a
[or
5A
of
capcity
current
minimum
a
with
operation,
RMS
250VAC
of
minimum
a
for
rated
be
must
cord
power
contact.
(earth)
ground
a
containing
plug
a
by
end
other
the
on
and
connection)
Power
(for
coupler
appliance
60320
IEC
an
by
end
one
on
terminated
conductor)
one
and
conductors
carrying
current
(two
type
three-conductor
a
be
must
cord
power
operation.
of
country
the
for
appropriate,
as
certified,
that's
cord
power
rated
correctly
a
only
Use
device.
the
with
supplied
not
is
cord
Injector.
Power
the
remove
and
install
should
personnel
qualified
and
trained
accidents.
preventing
for
practices
standard
review
Also,
device.
the
of
use
and
with
associated
hazards
any
for
document
this
review
equipment,
any
operating
Information
Introduction
When users purchase a Symbol WLAN solution, they often need to place access points in
obscure locations. In the past, a dedicated 24-hour, 90-264 VAC power source was required for
each access point in addition to the Ethernet infrastructure. This often required an electrical
contractor to install power drops at each access point location. With the Symbol Power Injector
solution (pt # AP-PSBIAS-1P2-AFR), centralized power can be provided for devices without a
local power supply for each.
Product Description
The Symbol Power Injector (pt # AP-PSBIAS-1P2-AFR) is a single-port, 802.3af compliant Power
over Ethernet hub combining low-voltage DC with Ethernet data in a single cable connecting
to an AP. The Power Injector's single DC and Ethernet data cable creates a modified Ethernet
cabling environment eliminating the need for separate Ethernet and power cables.
Data
Power
Power
Injector
to AP-5131 LAN
Port
AP-5131
Wireless LAN
(3)
(1)
Only
•The
the
voltage
•A
1.5A
•This
power
•Follow
power
Read
•
Warnings
(72-70762-01)
Guide
The
•
AP-PSBIAS-1P2-AFR)
AC
The
•
rated
following:
the
contain
The
•
sales
your
to
items
damaged
or
missing
any
report
Injector
ground
The
•
analysis.
network
site
and
survey
power
•A
site-specific
the
to
refer
procedures,
installation
•Only
installation
site-specific
provide
not
does
guide
use
to
guidelines
and
procedures
specifications,
provides
installation
device
and
networking
LAN-based
Ethernet
basic
with
Before
Injector.
Power
Symbol
the
installing
for
responsible
technician
Safety
The Power Injector is a small lightweight unit with a RJ-45 Ethernet cord input connector from
the hub on the front right-hand side of the unit and a RJ-45 data and power output connector
to the AP on the front left-hand side of the unit. On the back of the unit is a 110-220 VAC power
input.
A separate Power Injector is required for each device comprising the network.
The Symbol Power Injector supports the following Symbol device product families (all models
of the those listed):
•AP 100
•AP 200
•AP 300
•AP-5131
Caution - Using the Power Injector with an unsupported Symbol device could
render the device inoperable and void your warranty.
The Power Injector has the following features:
•Independent power controller (SPEAR™), CPU controller and input (Data) and output
(Data + Power) shielded RJ-45 connectors
•Supports standard 10/100BaseT Ethernet networks over a standard TIA/EIA-568
Category 5 (or higher) cabling
•Meets the IEEE 802.3af standard
•Universal AC Input: 110/220 V, 60/50 Hz.
•Minimum port output continuous allowable power of 15.4W at 48V
(minimum 12.95W at the PDTE)
•Underload, overload, short-circuit & under/over voltage port protection.
(4)
Installation
Injector
Power
•This
#
(pt
Injector
Power
•
should
packages
The
representative.
and
contents
package
the
Inspect
Contents
Package
Verifying
site
from
derived
documentation
site-specific
detailed
For
procedures.
Power-over-Ethernet
This
process.
installation
the
during
Injector
guide
This
concepts.
installation
familiar
is
technician
the
assumes
It
the
for
intended
is
guide
This
Installer
the
To
•Port Status and Main power LED indicators
•Standalone or wall mount installation support
• Interconnection option with other Power Injector units.
Technical Specifications
Physical Specifications
Width
Height
Depth
Weight
Environmental Specifications
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
Electrical Specifications
Input Voltage
Maximum Output Power
Nominal Output Voltage
Ethernet Interface
Input (Data In)
Output (Data & Power Out)
00
Guide
Installation
1-Port
Power
will
your
your
Installation
Preparing for Site Installation
The Power Injector can be installed free standing, on an even horizontal surface or wall
mounted using the power injector's wall mounting key holes.
The following guidelines should be adhered to before cabling the Power Injector to the Ethernet
source and Symbol device:
•Verify the device receiving converged power and Ethernet from the Power Injector is a
product approved by Symbol (AP100, AP200, AP300 and AP-5131).
58.5mm
31mm
•Do not block or cover airflow to the Power Injector.
145mm
450gr
•Keep the Power Injector away from excessive heat, humidity, vibration and dust.
0°C to 40°C (32°F to 104°F)
•The Power Injector is not a repeater, and does not amplify the Ethernet data signal. For
-20°C to 70°C (-4°F to 158°F)
optimal performance, ensure the Power Injector is placed as close as possible to the
10% to 93% Non-condensing
network data port. Do not configure the cable length between the Ethernet network
10% to 93% Non-condensing
source, the Power Injector and the Symbol AP beyond 100 meters (333ft).
Cabling the Power Injector
90VAC to 264VAC (47Hz - 63Hz)
.15.4 W
To install the Power Injector to an Ethernet data source and Symbol device:
48VDC
Ethernet 10/100Base-T
(RJ-45 female socket)
Ethernet 10/100Base-T, plus 48VDC
1. Connect the Power Injector to an AC outlet (110VAC to 220VAC).
RJ-45 female socket, with DC voltage
on pairs 7-8 and 4-5
2. Connect RJ-45 Ethernet cable between the network data supply (host) and the Power
Injector Data In connector.
3. Connect a RJ-45 Ethernet cable between the Power Injector Data & Power Out connector
and the Symbol device receiving converged power and Ethernet.
(5)
2006
January
A
Revision
72-70762-01
http://www.symbol.com/manuals/
to:
go
guide
this
of
version
latest
7360
945
118
+44
Operations
Distributor
call
or
distributor
local
Contact
Europe/Mid-East
US
Outside
+1-954-255-2610
Support
Sales
US
Inside
1-800-347-0178
America
Latin
Spain
Outside
40
324
91
+34
84452900
Sweden/Sverige
Spain
Inside
00
40
324
91
Spain/España
11-8095311
Africa
South
4375
2232
+47
Norway/Norge
315-271700
Netherlands/Nederland
5-520-1835
Mexico/México
2-484441
Italy/Italia
6074-49020
Germany/Deutschland
01-40-96-52-21
France
580
5407
9
Finland/Suomi
7020-1718
Denmark/Danmark
1-505-5794-0
Austria/Österreich
1-800-672-906
Australia
+65-6796-9600
Asia/Pacific
2424
328
0800
Kingdom
United
1-631-738-2400
905-629-7226
Canada
1-800-653-5350
States
United
Center:
Support
Symbol
the
contact
they
equipment,
the
with
problem
a
is
there
If
Support.
Systems
or
Technical
facility's
contact
equipment,
your
using
or
unit
your
running
problem
a
have
you
If
applications.
run
and
network
facility's
the
in
operate
to
configured
be
must
it
unit,
the
using
Information
Service
Caution - Ensure AC power is supplied to the Power Injector using an AC cable
with an appropriate ground connection approved for the country of operation.
(6)
the
For
Before
Advertisement
Table of Contents
Related Manuals for Symbol 1-PortPower-over-Ethernet
Summary of Contents for Symbol 1-PortPower-over-Ethernet
- Page 1 sockets. these connected should connectors data RJ-45 Only sockets. RJ-45 shielded ports Power & Data Data Injector Power •The outlet. particular that Injector Power connect voltage, outlet power from different label indicated voltage hazard. fire pose could damage equipment cause mismatch volatge •A...
- Page 2 All Symbol devices are designed to comply with rules and regulations in locations they are sold and will be labeled as required. Any changes or modifications to Symbol Technologies equipment, not expressly approved by Symbol Technologies, could void the user’s authority to operate the equipment.
Need help?
Do you have a question about the 1-PortPower-over-Ethernet and is the answer not in the manual?
Questions and answers