Related Manuals for Mangrove Jack's KEGERATOR Series
Summary of Contents for Mangrove Jack's KEGERATOR Series
- Page 1 KEGERATOR INSTRUCTIONS NO MORE BOTTLING! PERFECTLY CARBONATED BEER ON TAP FOR WHENEVER THE MOOD STRIKES. BREWING. OUR OBSESSION. BREWING. WWW.MANGROVEJACKS.COM OUR OBSESSION.
- Page 2 ITEMS INCLUDED TWO TAP KEGERATOR THREE TAP KEGERATOR • • 4 x Tap Tower Screws 4 x Tap Tower Screws • 1 x CO Gas Regulator • 1 x CO Gas Regulator • 1 x CO Cylinder Holder • 1 x CO Cylinder Holder •...
- Page 3 IMPORTANT SAFETY INSTRUCTIONS This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
- Page 4 1. PREPARATION • Remove all trays from inside the Kegerator body. • Read your CO Cylinder Safety Instructions that are provided with your cylinder. • Sit ends of your tubing that are not connected to anything in a jug of warm water to make the ends more malleable and easier to fit on to attachments.
- Page 5 4. ATTACHING THE CO 2 CYLINDER SUPPORT • Attach the cylinder support rack onto the 4 studs located at the back of the Kegerator. Align the holes in the cylinder support with the studs and push down firmly. 5. FITTING YOUR CO CYLINDER •...
- Page 6 7. ATTACHING THE BLACK LIQUID DISCONNECTS • Screw the MFL push fit connector to the threaded ball lock. • Push the hose into the opening of the push fit ball lock. 8. CONNECTING THE CO 2 CYLINDER • Check your CO Cylinder Safety Instructions for position of any nozzles and taps before starting this step.
- Page 7 9. FITTING AND CONNECTING YOUR KEGS • Attach a grey gas disconnect to the “IN” side of one of the Kegs. NOTE: To attach and detach you should push the centre of the disconnects down with your thumbs while pulling the bottom up with your fore-fingers. •...
- Page 8 USING YOUR KEGERATOR 1. OPENING THE CO 2 CYLINDER MAIN VALVE: Step 1: With all your hoses and the keg connected turn the pressure on the CO 2 regulator up to • Before opening the main valve located on the top 140kPa (about 20 psi) then turn off the valve on the of the CO 2 cylinder, make sure the secondary top of the CO 2 gas cylinder.
- Page 9 OPERATING INSTRUCTIONS 1. REPLACING AN EMPTY CO 2 CYLINDER: • Adjust the pressure to 30 psi and leave for 2 days. • Close the main cylinder valve by turning in a • Drop pressure to about 12 psi and leave for one clockwise direction.
- Page 10 gas pressure on your keg to 14 PSI at 3°C and still cleaning process it will leave an unsanitary surface get a perfect pour. This should pour a beer with a that can harbour microorganisms which will cause head, at a good speed and the beer should have undesirable flavour and/or cause the beer to go enough gas to continue to release gas throughout flat.
- Page 11 Mangrove Jack’s Kegerator 36 Month Warranty • This Kegerator comes with a full 36 month warranty against any manufacturer faults or defects. • This warranty does not cover any faults or defects caused by power surges, exposure to excessive water or outside weather conditions, or any operation outside the uses stated in the instruction manual.
- Page 12 See Mangrove Jack’s for all your homebrewing and beer dispensing needs. BREWING. OUR OBSESSION. WWW.MANGROVEJACKS.COM WWW.MANGROVEJACKS.COM Version: 4...
Need help?
Do you have a question about the KEGERATOR Series and is the answer not in the manual?
Questions and answers
FRIDGE STARTED TO DE-FROST , THEN SHUT DOWN , I TURNED OFF AT THE POWER POINT . THAT WAS 3 DAYS AGO . FRIDGE WILL NOT RE START , WHEN TURNED BACK ON , TEMP LIGHT COMES ON FOR 2 -3 SECONDS , NO OTHER FUNCTIONS WORK , THEN SHUTS DOWN AGAIN . NOT 2YRS OLD . UNDERSTAND WARRANTY TO BE 36 MNTHS,