Table of Contents
Advertisement
Quick Links
09/19-W13-Wei
Instructions for use 739 948
Scope of delivery:
1
Electric vehicle charging station, 739 948
2
4 mm safety bridge connector orange
3
4 mm safety bridge connector black
1
CEE connection cable 400 V/16 A, 3 m
1
Instructions for use 739 948
LEYBOLD DIDACTIC GMBH . Leyboldstrasse 1 . D-50354 Hürth, Germany . Phone +49 2233 604-0 . Fax +49 2233 604-222 . e-mail: info@leybold-
didactic.de
by Leybold Didactic GmbH
1
Activate "Charging"
2
Operating mode dis-
play
3
Ready indicator
4
System interface
MODBUS RTU
5
Measuring sockets
5a
CP signal (left)
5b
PP/CC signal (right)
6 Measuring sockets
L1 and N
7
Main contactor indi-
16
cator
8
Trip RCCB with
DC/AC switching and
knob
17
9
Charging
socket
with hinged lid and in-
terlock
10
Schuko socket
230 V~
0. Intended use
The "electric vehicle charging station" device is a teaching aid for
vehicle high-voltage technology training.
The device allows the trainee to perform typical workshop meas-
urements realistically.
Together with the automotive high voltage trainer, 739 947, the
device is used to create an electric vehicle charging infrastructure
situation. A three-phase passive charging cable or a single-
phase active charging cable can be connected.
Electric vehicle charging station
11
RJ45 connector
(Option!)
12
Fault switch
13
RCCB Type B
14
Triple fuse
(charging socket)
15
Fuses
single
Power supply con-
nection 3*400 V,
50/60 Hz
Connection auto-
motive high voltage
trainer,
739 947
Printed in the Federal Republic of Germany
Technical alterations reserved
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for LD Didactic 739 948
-
Page 1: Intended Use
0. Intended use Scope of delivery: The “electric vehicle charging station” device is a teaching aid for Electric vehicle charging station, 739 948 vehicle high-voltage technology training. 4 mm safety bridge connector orange The device allows the trainee to perform typical workshop meas- urements realistically. - Page 2 Instructions for use 739 948 Page 2/6 Safety Information Read these instructions for use completely before commissioning and operating the device! • Failure to observe these operating instructions will void the Measurements on all 4 mm measuring sockets may only warranty/guarantee.
- Page 3 Instructions for use 739 948 Page 3/6 ≈ +6.7 V, PWM active: Charging Status C «Charging» Activate the charging station by actuating enabling switch Activate the “charging” switch on the automotive high voltage trainer, 739 947 The main contactor switches the charging voltage on and blue indicator light lights up.
- Page 4 Instructions for use 739 947 Page 4/6 Fig. 5 - Fault simulation of the CP contact Checking the residual current circuit breaker (“RCCB”) RC can be tripped while charging. To do this, first activate fault Fig. 7 - 13 A #F5 and set the potentiometer to the left stop.
- Page 5 Instructions for use 739 948 Page 5/6 Establishing a connection The communication signals between the vehicle and charging station can also be measured on the automotive high voltage need RS485 interface (e.g. LEYBOLD trainer, 739 947 at the intended 4 mm measuring socket for CP 735 315USB), optionally a 9-pin serial standard connec- against the PE socket while charging.
-
Page 6: Technical Data
Instructions for use 739 947 Page 6/6 5. Monitoring software Follow the steps to establish a connection as described under at the time this document was cre- 4.2. You can download ated the «EV CC Device Monitor» program from PHŒNIX CONTACT in order to display various information directly and make changes.
Need help?
Do you have a question about the 739 948 and is the answer not in the manual?
Questions and answers