Do you have a question about the Steelcraft AX910 Series and is the answer not in the manual?
Questions and answers
Subscribe to Our Youtube Channel
Summary of Contents for Britax Steelcraft AX910 Series
Page 1
BABY ROCKER WITH TOY BAR IMPORTANT: KEEP THIS BOOKLET IN A SAFE PLACE FOR FUTURE REFERENCE. www.britax.com.au Series AX910...
Page 2
WARNINGS ALWAYS FOLLOW THE MANUFACTURERS INSTRUCTIONS. READ ALL INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY AND USE OF THIS ROCKER. THE CORRECT USE AND MAINTENANCE OF THIS PRODUCT IS ESSENTIAL. WARNING: THE CHILD SHOULD BE SECURED IN THE ROCKER AT ALL TIMES WITH THE CROTCH STRAP. NEVER USE THE LAP BELT ONLY.
Page 3
WARNINGS WARNINGS: • DO NOT ALLOW CHILDREN TO USE THE ROCKER AS A TOY OR INTERFERE WITH THE ROCKER WHEN IN USE. • DO NOT LEAVE THE ROCKER AND ITS ACCESSORIES NEAR AN OPEN FIRE OR EXPOSED FLAME. • DO NOT POSITION THE ROCKER NEAR ANY WINDOW COVERING CORDS, ELECTRICAL CORDS OR ANY OTHER LOOSE CORDS OR CABLES.
ROCKER ASSEMBLY OPENING THE ROCKER FRAME WARNING: ENSURE THAT ALL THE LOCKING DEVICES ARE ENGAGED INTO POSITION BEFORE USE. A To open the rocker, rotate the bottom rail from the front of the rocker to the back of the rocker until the frame has locked.
ROCKER ASSEMBLY ATTACHING THE CANOPY IMPORTANT NOTE: The sun is very strong. DO NOT LEAVE YOUR CHILD EXPOSED TO THE SUN. The canopy or hood on this product will not give your child total protection from the harmful rays of the sun. A To attach the canopy, clip the canopy moulding onto both sides of the rocker frame.
Page 6
ROCKER ASSEMBLY ATTACHING THE TOY BAR WARNING: NEVER USE THE TOY BAR TO LIFT OR CARRY THE ROCKER. A Attach the clip on each end of the toy bar to the round part of the canopy frame. B To adjust the canopy, open by pulling forward, or close by pushing backward.
Page 7
ROCKER ASSEMBLY ATTACHING THE TOY BAR D Attach toys to the toy bar by fitting the strap located at the top of the bar through the loop on the top of the toy. E Firmly grip the top frame of the toy bar and move to the desired position.
Page 8
ROCKER OPERATION USING THE HARNESS WARNING: THE CHILD SHOULD BE SECURED IN THE ROCKER AT ALL TIMES WITH THE CROTCH STRAP. NEVER USE LAP BELT ONLY. ADJUST THE LAP BELT TO FIT FIRMLY BUT COMFORTABLY AROUND THE CHILD. A Place the child in the rocker and position the crotch strap between legs.
Page 9
ROCKER OPERATION USING THE HARNESS C To release the buckle, squeeze the top and bottom buckle prongs with enough pressure so the buckle prongs release from the buckle housing.
Page 10
ROCKER OPERATION USING THE ROCKER IN THE STATIC OR ROCKING MODES WARNING: REMOVE THE CHILD FROM THE ROCKER BEFORE ADJUSTING THE ROCKER INTO STATIC OR ROCKING MODES. A To set the rocker into a static position, rotate the rear leg stand back. B To set the rocker into the rocking position, rotate the rear leg stand forward.
Page 11
ROCKER OPERATION ADJUSTING THE SEAT ANGLE WARNINGS: • DO NOT USE THE MOST VERTICAL POSITION. • THE UPRIGHT POSITIONS ARE NOT SUITABLE FOR USE WITH CHILDREN LESS THAN 6 MONTHS OLD. • REMOVE THE CHILD FROM THE ROCKER BEFORE ADJUSTING THE SEAT POSITION.
Page 12
ROCKER OPERATION ADJUSTING THE SEAT ANGLE WARNINGS: • DO NOT USE THE MOST VERTICAL POSITION.
Page 13
ROCKER OPERATION FOLDING THE ROCKER WARNING: REMOVE THE CHILD FROM THE ROCKER BEFORE COMMENCING ANY FOLDING OPERATION. A For compact storage, fold canopy and toy bar back. B Release the locking catch, and pull the frame apart until bottom rail is fully disengaged.
CARE AND MAINTENANCE • To prolong the life of your rocker keep it clean and do not leave it in the direct sunlight for extended periods of time. • Removable fabric covers and trims may be cleaned using warm water with a household soap or mild detergent.
Page 16
CUSTOMER SERVICE 1300 303 330 - Australia 0508 688 822 - New Zealand Due to our continuing program of development, Britax reserves the right to alter the specifications, color or design without any further notice. The Steelcraft trademark is the property of Britax Childcare Pty.Ltd - Australia.
Need help?
Do you have a question about the Steelcraft AX910 Series and is the answer not in the manual?
Questions and answers