Summary of Contents for F(x)tec Pro1
- Page 1 F(x)tec Pro 1 QUICK START GUIDE OTHER LANGUAGE 2 OTHER LANGUAGE 3 OTHER LANGUAGE 4 OTHER LANGUAGE 5 OTHER LANGUAGE 6...
-
Page 2: Getting To Know Your Phone
QUICK START GUIDE Thank you for choosing the Pro 1 . Before using the device, please read this guide to help you get started. The full User Guide is available at www.fxtec.com/support. Getting To Know Your Phone Familiarise yourself with the different parts of the phone as shown in the diagram below. - Page 3 Sliding Your Phone Open 1. Lift the right side of the Pro 1 up slightly. 2. Slide the screen up until the hinge locks into position pg. 3...
-
Page 4: Inserting And Removing The Sim Card
Inserting and Removing the SIM card 1. To open the SIM card tray, place your fingernail into the ridge and carefully slide the tray out. 2. Put the nano-SIM card into the slot located on the tray with the contact area facing down. 3. -
Page 5: Charging Your Phone
Charging Your Phone To charge the phone, use the charger provided with your phone. The charger type may vary according to country. Please use the one that is relevant to your region. Plug the charger into a wall outlet and connect the cable to the phone. A charging indicator will be displayed to indicate the phone is charging. -
Page 6: Safety Information
Safety Information Read all safety information before using the device to prevent injury to yourself or others, to prevent damage to your device and to avoid breaking local laws and regulations. See the full ‘Important Safety Information’ at www.fxtec.com/support. Handle Device with Care The screen of this device is made of glass. - Page 7 Check with your local waste authority for information on your nearest recycling point. Regulatory Information: EU EU Compliance Notice Hereby, FX Technology Limited declares that Pro1 is in compliance with Directive 2014/53/EU (Radio Equipment Directive). The full declaration of conformity is below: EU Declaration of Conformity...
- Page 8 Draft EN 301 489-19 V2.1.0 Draft EN 301 489-52 V1.1.0 EN 55032:2015/AC:2016 Class B EN 55035:2017 Spectrum EN 300 328 v2.1.1 (Article 3.2 of the RED) EN 301 893 v2.1.1 EN 301 511 V12.5.1 EN 301 908-1 V11.1.1, EN 301 908-2 V11.1.2, EN 301 908-13 V11.1.2 EN 300 328 V2.1.1, EN 301 893 V2.1.1...
- Page 9 Radio frequency interference FX Technology Limited is not responsible for any radio or television interference caused by unauthorized modification of these devices or accessories, or by the substitution or attachment of connecting cables and equipment other than that specified by FX Technology Limited.
-
Page 10: Regulatory Information: United States
Regulatory information: United States U.S. Federal Communications Commission’s (FCC) Regulatory Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. -
Page 11: Regulatory Information: Canada
Hearing Aid Compatibility (HAC) The Pro 1 has been evaluated and certified to be compatible with hearing aids per technical specification ANSI C63.19-2011. There are two measures of hearing aid compatibility: M rating, which is a measure of immunity to radio frequency interference for acoustic coupling hearing aids;... - Page 12 Pro 1 maximum SAR values as reported to the ISED are: • 0.375 W/kg when holding it to your ear • 0.397 W/kg when properly worn on the body This device has been certified for use in Canada. Status of the listing in the ISED’s REL (Radio Equipment List) can be found at the following web address: http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do Additional Canadian information on RF exposure also can be found...
- Page 13 pg. 13...