Easy wave RTS40 Series Quick Start Manual

GB Motion Detector RTS40
Model
(2)
(1) RTS40E5001-01
(2) RTS40E5001-02
Technical Details
Frequency: 868.3 MHz
Radiated power: 0,89 mW
Modulation: FSK
Coding: Easywave A/B
EasywavePlus
Power supply: 2x 3-V-Batterie, CR2032
Temperature: -20 °C to +60 °C
Range: free-field: approx
buildings: approx
Brightness range: 1 lx to 150 lx
Follow-up time: 1 s to 131 min
Inspection density: approx. 16 m²
Dimensions: cover: 55x55x12 mm
plate: 71x71x1.5 mm
Weight: 34.0 g
Scope of Delivery
Transmission module, 2 batteries CR2032,
cover, mounting plate, attachment set,
operating instructions
Intended Use
Only use the device as a motion detector and only
for operating Easywave radio receivers.
The manufacturer shall not be liable for any
damage caused by improper or non-intended
use.
Safety Advice
Before using the Radio Wall Switch,
carefully read through the operating in-
structions!
Also note the operating instructions of the
receiver(s)!
Do not make any unauthorized alterations or
modifications to the RadioWall Switch!
Have faulty Radio Wall Switches checked by
the manufacturer!
Keep the batteries out of the reach of children!
Function
The RTS40 is a battery-operated wireless moti-
on detector for indoor use. Movement is detected
and information sent via an Easywave message,
and the connected Easywave radio receivers
are operated in line with their selected operating
mode.
There are two device options available:
AUTOMATIC operation (RTS40E5001-01)
The motion detector automatically reacts as per
the programmed values.
ON/OFF/AUTO operation (RTS40E5001-02)
The function of the motion detector can be opera-
ted as permanently ON, permanently OFF or on
automatic operation.
The interval before the load is switched off (fol-
low-up time) can be selected in seconds and in
minutes and be extended by a factor if necessary.
The follow-up time can be retriggered. With each
detected movement before end of time, the fol-
low-up time starts again.
(1)
The integrated light sensor can be activated and
deactivated manually. The connected radio recei-
ver operates if the light sensor is activated and
a movement is detected, and the programmed
AUTO brightness is not met.
If the light sensor is deactivated, the motion de-
ON/OFF/AUTO
tector works independently of the brightness.
Start-Up
General information (Figure 1)
The motion detector is equipped with a PIR sen-
sor and suitable for ceiling and wall installation.
The sensor reacts to changing heat radiation. The
motion detector should therefore not be installed
near heat sources, air currents or objects that
move.
150 m
.
30 m
.
C
B1
A
G
The distance between the installed object and
light sources should be at least 0.5 m.
No heat radiation is detected through barriers
(walls, glass panes, etc.).
Make sure there is no interference with the wire-
less connection. Do not mount the device in a dis-
tribution box, in metal casings, in direct proximity
to large metal objects, on the floor or close to it.
Mounting (Figure 2)
1. Screw or stick the mounting plate to the instal-
lation site.
2. Insert the batteries. The positive pole has to
be visible!
3. Memorize the transmission code in the
receivers. For this, set the receive to learn
mode. You can do this directly on the recei-
ver or via the learn button PTx of this trans-
mitter. Please read the operating instructions
supplied with the receivers.
Press now the W button (Easywave code A)
or F (Easywave code B) on the transmitting
module. Set the required time and brightness
settings or use the factory settings (see "Set-
tings").
4. Place the cover frame on the mounting plate,
latch the transmitting module onto the snap
arm and clip on the cover.
ceiling mounting
51°
~ 4.0 m
D
C
B2
A
B1
B2
PTx
PTx
C
D
E
F
G
Figure 1
wall mounting
51°
~
2.5 m
Figure 2
F
E
Cover
Transmission module front
Transmission module back
Learning button
Battery CR2032
Cover frame
(Not in the delivery)
Mounting plate
Catches
Radio receiver Easywave