Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for Maytronics HeatMiser II
- Page 1 5237842...
- Page 2 Table of Contents Solara Installation guide. © 2013, all rights reserved P a g e...
-
Page 3: Table Of Contents
Troubleshooting ........................16 DISABLING A DAMAGED RISER TUBE ..................17 Maytronics, US Inc. 1790 Corporate Drive, Suite 300 Norcross, GA 30093 www.maytronicsus.com e-Mail: info@maytronicsus.com Ph: 1-888-DOLPHIN (356-7446) HeatMiser II Installation guide. © 2014, all rights reserved P a g e... -
Page 4: Preface
Safety precautions and regulations PREFACE HeatMiser II has been engineered and manufactured according to the highest standards for reliability, durability, ease of installation, operation and safety. With proper care, HeatMiser II will heat your pool and water during your swimming season for many years to come. Thank you for purchasing HeatMiser II. -
Page 5: General Information
As cold water is fed into the HeatMiser II, it flows through the individual riser tubes in the incased glazing. The sun radiation is harvested by the collector and heats the water in the tubes which is carried back into the pool. -
Page 6: Unpacking The Solar Collector
Use the supplied stand to angle the collector so it is facing the sun. NOTE: HeatMiser II must be installed between the filter and the pool water inlet, AFTER the water is filtered to prevent dirt and debris from clogging the riser tubes. -
Page 7: Parts List
Stabilizes stand (in a small plastic bag) String Stabilizes stand (in a small plastic bag) Repair plug Disable a leaking riser tube (in a small plastic bag) HeatMiser II Installation guide. © 2014, all rights reserved P a g e... -
Page 8: Installation Instructions
Positioning the solar collector INSTALLATION INSTRUC TIONS Please follow the instructions to ensure a safe and quick installation of the HeatMiser II panel to the existing pool/equipment. These instructions assume that the pool and filter system are already assembled and there is a hose attached to the pool return (pool water inlet). - Page 9 Repeat steps 2 through 5 on the other panel. Turn the solar collector so it is facing the sun. Make sure the stands are stable on the ground. HeatMiser II Installation guide. © 2014, all rights reserved P a g e...
-
Page 10: Set Up Panels
Push both ends of the connector over the top outlets of each panel. Slide the metal hose clamps over the outlet and tighten firmly with a screwdriver. HeatMiser II Installation guide. © 2014, all rights reserved P a g e | 10... - Page 11 Rubber end cap with Rubber end cap with metal hose clamp metal hose clamp 2 Rubber end caps with metal hose clamp one on each outlet HeatMiser II Installation guide. © 2014, all rights reserved P a g e | 11...
-
Page 12: Connecting Solar Collector To Filter Pump
Teflon tape (not supplied) to adapter threads and screw the hose directly to the adapter. NOTE: When connecting the HeatMiser II, make sure the 'O ring' stays in place and doesn't get pinched. NOTE: When installing HeatMiser II allow for removal of the collector for winterizing. - Page 13 Installation instructions Connecting Solar collector to pool Before installing the solar heater After installing the solar heater Solar collector Filter and Pump Pool outlet Pool inlet HeatMiser II Installation guide. © 2014, all rights reserved P a g e | 13...
-
Page 14: Connecting Several Solar Collectors Together (Optional)
Connecting several solar collectors together (optional) CONNECTING SEVERAL S OLAR COLLECTORS TOGE THER (OPTI ONAL) Connecting several units will offer a higher temperature. The HeatMiser II is a modular unit that can be connected to additional ones if required. When the solar collectors are positioned and standing, use the rubber connector and metal hose clamp (supplied) to connect one unit to another as shown below. -
Page 15: Initial Operation
Do not allow standing water inside the solar collector to freeze. Water expands as it freezes and can rupture the riser tubes of the collector. HeatMiser II Installation guide. © 2014, all rights reserved P a g e | 15... -
Page 16: Troubleshooting
Metal Hose Clamp around the Hose Adapter Fitting. Absorber leaks - disable the leaking riser tube according to the instructions on page 17. HeatMiser II Installation guide. © 2014, all rights reserved P a g e | 16... -
Page 17: Disabling A Damaged Riser Tube
Important: Do not use a wider chisel than ¼ inch, as you might damage the adjacent risers as you remove the damaged one. HeatMiser II Installation guide. © 2014, all rights reserved P a g e | 17... - Page 18 9 Move back the glazing to its original position and re-attach the stoppers. 10 The panel is now leak free while its uniform appearance is restored. HeatMiser II Installation guide. © 2014, all rights reserved P a g e | 18...
Need help?
Do you have a question about the HeatMiser II and is the answer not in the manual?
Questions and answers