DELTACALOR DRYER ELECTRIC PLUS Operation And Installation Manual

Dryer electric plus electric towel heater and clothes rack

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

DRYER ELECTRIC PLUS

Electric towel heater and clothes rack

OPERATION AND INSTALLATION MANUAL

These instructions must be read carefully to ensure the product operates

safely. We would therefore strongly recommend reading them before starting

on installation and keep them for future reference. Call a qualified technician

for help if you have any doubts about installing the product.

DOC.IS.002529

04.04.2016

Table of Contents

Need help?

Do you have a question about the DRYER ELECTRIC PLUS and is the answer not in the manual?

Questions and answers

Summary of Contents for DELTACALOR DRYER ELECTRIC PLUS

Page 1 DRYER ELECTRIC PLUS Electric towel heater and clothes rack OPERATION AND INSTALLATION MANUAL These instructions must be read carefully to ensure the product operates safely. We would therefore strongly recommend reading them before starting on installation and keep them for future reference. Call a qualified technician for help if you have any doubts about installing the product.
Page 2: Safety Instructions
SAFETY INSTRUCTIONS • Should damages be caused from breach of these regulations, the manufacturer’s guarantee shall be invalidated. • Do not use the appliance outdoors. • Your appliance is intended for domestic use. It may not be used for other purposes. •...
Page 3 WARNINGS FOR DISABLED PEOPLE AND CHILDREN • This equipment may not be used by people with reduced phys- ical, sensory, or mental capacity, those without any knowledge of the equipment, or children over 8 years of age, unless super- vised and instructed on safe use of the equipment, and aware of all the risks.
Page 4: Children Safety
CHILDREN SAFETY Keyboard lock “ ” To enable or disable the keyboard lock, press and hold the DRYER button for 5s. 5 sec When keyboard lock function is enabled, the device continues op- eration with default settings. In this mode, it is not possible to modify the program settings or the temperature, or to activate the BOOST or DRYER functions.
Page 5: Preparation For Installation
PREPARATION FOR INSTALLATION Before connecting the heating appliance, disconnect the power supply using the general switch. This heating appliance is a class II appliance. As such, it may be in- stalled in all rooms of the house, including in protection volumes 2 and 3 of a bathroom (IP24).
Page 6: Power Supply And Electrical Connections
POWER SUPPLY AND ELECTRICAL CONNECTIONS • In accordance with the rules in force, the power of the heating • In accordance with the rules in force, the power of the heating appliance must be protected by an RCD of 30 mA and an over- appliance must be protected by an RCD of 30 mA and an over- current protection device, suitable to the characteristics of the current protection device, suitable to the characteristics of the...
Page 7 WALL MOUNTING THE FIXING KIT 3 × 3 × Ø 10 NOTE The screws and anchors are not supplied. [ 7 ]...
Page 8: Installation
INSTALLATION WHITE Power 500 W 750 W Power with hot air blower 1500 W 1750 W 380 mm 380 mm 385 mm 625 mm How to install: ensure that the device plastic spacers rest against the rear wall. [ 8 ]...
Page 9: Correct Use
CORRECT USE Use the product as shown in figure 1. Never cover the entire unit with towels or clothing (figure 2). The manifolds (vertical pipes) cannot be covered. Incorrect use can cause dangerous overheat- ing, and compromise how the equipment works. To clean the equipment, do not use chemical products, but only a non abrasive damp cloth.
Page 10: Operation
OPERATION Synoptic BOOST button (BOOST ON/OFF switch and + MORNING, EVENING temperature setting programming) (over temperature cancelled Programme selector switch and reset) Programme indicator and BOOST LED towel warmer heating LED Keyboard lock DRYER LED Endurance indicator LED DRYER button ( DRYER + keyboard lock) COMFORT MORNING...
Page 11 ON/OFF mode and temperature setting OFF mode: rotate the selector switch counter-clockwise until the limit stop. All LEDS are off, the heated towel rail and the device are off. All functions are disabled. WARNING -The room temperature may drop below 0°C in this mode. A mechanical lock allows you to identify the OFF position.
Page 12 AUTO mode (this function is only enabled on models without a plug, and with a “pilot wire” connecting wire) Press the comfort mode temperature set on the selector switch, to adjust room temperature through the signals received from the pilot wire by only using the resistance of the heated towel rail.
Page 13 MORNING mode programme: the ON/OFF selector turned to the required ambient tempera- ture (position other than OFF). Press the BOOST button for 5 seconds. 5 sec The BOOST, DRYER and 15 min LEDS will start flashing. Do the next operation within 5 seconds.
Page 14 If the user wishes to change the duration or the programme’s start time, the procedure will be started all over. If the user modifies the programmes selector mode, the programme will not be recorded if it is moved from the MORNING mode before the programme is confirmed. The MORNING mode is saved;...
Page 15: Boost Mode
BOOST mode The device will operate at reduced fan speed in BOOST mode. The heated towel rail resistance will be enabled. The room temperature is limited to 35°C. The device will continue running at a reduced speed up to 34°C; beyond this temperature adjust by using the heated towel rail resistance.
Page 16 5s after the last brief pressure, the BOOST programme is enabled. The BOOST LED stops flashing. 5 sec The duration LEDS start the countdown to indicate the time left. The BOOST LED is steady red as long as the device warms up. The ON/OFF LED is steady red as long as the heated towel rail resistance is enabled.
Page 17 The DRYER and the 15 min leds will start flashing. Press the DRYER button briefly to change duration within 5s. The duration selected will be displayed with a green flashing LED. 5s after the last time the button is pressed the DRYER programme is enabled.
Page 18 Clarifications on the BOOST and DRYER modes The BOOST and DRYER modes are essential No need to cancel one or the other mode to switch between them. The device is in the BOOST mode: • Press BOOST button => the BOOST mode stops. •...
Page 19: Reset Function
Clarifications on the keyboard lock mode When activating the keyboard lock, the set mode and the temperature set point are recorded. If the keyboard lock is enabled: • The device will return to the modes and temperature set-point before using the keyboard lock feature if there is a power outage after the next recovery.
Page 20: Temperature Error
Temperature error Flashing LED red / green alternately The problem may be due to incorrect reading of the => temperature error inside temperature sensor. The user cannot intervene to solve the problem. Flashing LED red / green alternately Internal overheating. + BOOST/DRYER led alternately Thermo mechanical security on device internal =>...
Page 21 CARE AND MAINTENANCE OF THE ANTI-DUST FILTER The device is equipped with a removable dust filter which retains the impurities in the air sucked from the room. Dust amount can stop the appliance. Turn off the device before cleaning the filter. To do this, if possible disconnect the power supply to the device and move the temperature selector to OFF.
Page 22 HEATING AND DRYING FUNCTION The grid can be adjusted manually on 7 different positions, between 0° and 90°, so that the air flow output is adjusted as required. To direct the grid, it must be moved, as shown in the figure, to the required position. Each position is identified clearly by a “clack!”...
Page 23 INSTRUCTIONS FOR USE: RECOMMENDATIONS Heating bathroom (BOOST p.15) Use BOOST mode. The device resistance and the heated towel rail will be enabled based on the selected period. The recommended position for the front grid is vertical (0°). Clothes dryer (DRYER p.16) Use DRYER mode.
Page 24: Troubleshooting
TROUBLESHOOTING No LED lights. • Ensure the ON / OFF-TEMPERATURE switch is not OFF. • Ensure power is adequately supplied to the heated towel rail. Room temperature is not enough; the heated towel rail seems not to be sufficiently hot. •...
Page 25: Technical Specifications
• Thermo-mechanical security on device resistance. • Clogged filter or fan malfunctions via CTN thermal probe. • Heated towel rail resistance + device: 500W+1000W o 750W+1000W (resistance load). Manufacturer: DELTACALOR s.r.l. Instruction manual available from: http://www.lfantoni.com/d/DOC.IS.002529-EN-dryer-electric-plus.pdf symbol applied to the product means that it is compulsory to consign the appliance to a special waste collection centre in case of disposal, in conformity to the 2002/96/EC Directive.
Page 26 [ 26 ]...
Page 28 DELTACALOR s.r.l. Via Mazzini 23801 • Calolziocorte (LC) Italy www.deltacalor.com...