Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for Home HME030236N
- Page 1 WATER DISPENSER HME030236N...
-
Page 3: Table Of Contents
TABLE OF CONTENTS Important Safety Instructions Parts Description Operation 9-10 Cleaning And Maintenance Troubleshooting Warranty Manufacturing Info Warning Contact Us... - Page 4 BEFORE FIRST USE: To prevent any internal damage, it is very important to keep refrigeration units (like this one) upright throughout their journey. Please leave it standing upright and outside the box for 24 HOURS before plugging it in.
- Page 5 Congratulations on bringing home your new appliance! Don’t forget to register your product at homelabs.com/reg for updates, coupons, and other relevant information. Although greatly appreciated, product registration is not required to activate any warranty.
-
Page 6: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of injury and property damage, the user must read this entire guide before assembling, installing, operating, and maintaining the dispenser. Failure to execute the instructions in this manual can cause personal injury or property damage. -
Page 7: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS • This appliance should be operated in environments with temperatures from 38°F~100°F and humidity ≤ 90%. • This appliance is not suitable for installation in an area where a water jet could be used. • Never turn the machine upside down or lean it at more than 45°. •... -
Page 8: Parts Description
PARTS DESCRIPTION NOTE: This machine is suitable for a 3- or 5-gallon bottle. Do NOT use hard water as it can cause scale inside of boiler, and influence the heating speed and performance. This unit has been tested and sanitized prior to packing and shipping. During transit, dust and odors can accumulate in the tank and lines. -
Page 9: Operation
OPERATION OPERATING INSTRUCTIONS LOCATING DISPENSER 1. Place the dispenser upright. 2. Place the dispenser on a hard, level surface; in a cool, shaded location near a grounded wall outlet. Note: Do NOT plug in the power cord yet. 3. Position the dispenser so the back is at least 8 inches from the wall and there is at least 8 inches of clearance on both sides. ASSEMBLING 1. - Page 10 OPERATION CHANGING BOTTLES A flashing red light alerts you when your bottle is empty. Replace the bottle as soon as possible. CAUTION: Do not dispense hot or cold water if the red light is flashing as you could empty the tanks and cause the dispenser to overheat.
-
Page 11: Cleaning And Maintenance
CLEANING AND MAINTENANCE To avoid an accident, cut off the power supply before cleaning according to the following instructions. The cleaning must be under the guidance of professional staff. Cleaning: We suggest that you contact professional cleaning service for cleaning. CAUTION: This unit dispenses water at temperatures that can cause severe burns. -
Page 12: Troubleshooting
•Make sure green power switch on the back of the dispenser is turned ON. •If water hasn't been cold yet, please contact a service technician or hOme ™ support team for assistance. -
Page 13: Warranty
(“warranty period”) on all of our products purchased new and unused ™ from hOme Technologies, LLC or an authorized reseller, with an original proof of purchase and where a defect has arisen, wholly or substantially, as a result of faulty manufacture, parts or workmanship during the warranty period. - Page 16 1-800-898-3002 For Indoor Use Only © 2018 hOme Technologies, LLC help@homelabs.com 37 East 18 Street, 7th Floor homelabs.com/help New York, NY 10003...
Need help?
Do you have a question about the HME030236N and is the answer not in the manual?
Questions and answers
Dispenser will not power on
The Home HME030236N dispenser may not power on due to the following reasons:
1. The power cord is not properly connected to a working outlet.
2. The green power switch on the back of the dispenser is turned off.
Ensure the power cord is securely plugged into a functional outlet and the green power switch is turned on.
This answer is automatically generated
The hose is not sucking up water, 1/10 into a new 5 gal
The Home HME030236N hose may not be sucking up water due to the following reasons:
1. The power cord is not properly connected to a working outlet.
2. The dispenser has not been set up correctly, and the probe assembly is not properly placed in the water bottle.
3. The collar has not been slid down until it clicks in place, or the head is not pushed down far enough for the tubes to reach the bottom of the bottle.
4. The pump has not had enough time to move water to the hot and cold tanks (it takes up to 12 minutes for the first fill).
5. The green power switch on the back of the dispenser is not turned on.
Check these factors to ensure proper operation.
This answer is automatically generated
No water is coming out of the dispenser. Just started happening 1/10 of the way through a new 5 gal.
No water is coming out of the dispenser because:
- The bottle may be empty; replace it with a full one.
- The red child lock button must be slid and held while pressing the hot water button.
This answer is automatically generated
Water is leaking from the bottom of the smaller water tank