What’s in the Box? • (1) Color CCD Infrared Weather Resistant Wireless Camera • (1) 7" TFT LCD Color Wireless Monitor with Standard U-Bracket Mount, Suction Cup Pedestal Mount, Built In Power Harness • (1) Sun Shade • (2) Wireless Antennas •...
Introduction Please read all of the installation instructions carefully before installing the product. Improper installation will void manufacturer’s warranty. Congratulations on purchasing a Rear Observation System With Night Vision Camera. With this manual you will be able to properly install and operate the unit. The Rear Observation System is intended to be installed as a supplement aid to your standard rear view mirror that already exists in your vehicle.
Safety Information Please read the entire manual and follow the instructions and warnings carefully. Failure to do so can cause serious damage and/or injury, including loss of life. Be sure to obey all applicable local traffic and motor vehicle regulations as it pertains to this product. Improper installation will void manufacturer’s warranty.
Safety Information • Electric shock or product malfunction may occur if this product is installed incorrectly. • Use this product within the voltage range specified. Failure to do so can cause electric shock or product malfunction. • Take special care when cleaning the monitor. •...
Before Beginning Installation Before drilling please check that no cable or wiring is on the other side of the wall. Please clamp all wires securely to reduce the possibility of them being damaged while vehicle is in use. Keep all cables away from hot or moving parts and components causing electrical interference.
Page 8
Before Beginning Installation Camera The camera and monitor will require their own power sources routed individually to each component. They do not have a cable that interconnects. Do not run power wires over sharp edges. Keep power wires away from HOT and/or rotating parts such as, but not limited to, exhaust systems and drive shafts.
Installation Guide The Power Harness • Both the monitor and camera require their own individual power sources. Connect the (RED) +12VDC wire to ignition/switched on power and the ground (BLACK) wire to chassis ground. If interference occurs or camera has difficulty connecting to the monitor, try tying the ground wire into an existing ground wire or run a ground directly to battery.
Page 10
Pairing 1. Power ON the monitor and be sure that power is available to the camera. 2. Toggle the "MENU" button on the monitor. 3. Make sure that "Pairing" is selected in the menu and toggle the "MODE" button. This allows you to now select which camera channel the included camera links too.
Standard U-Bracket Monitor Installation 1. Remove the thumb and allen screw from the monitor then remove monitor. Place bracket in desired location and fasten down with 3 screws. (See below pictures) 2. Using the thumb and allen screws put the monitor into the bracket, adjust angle, and lock it.
Installation Diagram 4 Pin Connection NOTE: Diagrams are for installation reference only, monitor and camera are a representative image PAIRING SWITCH MIRROR (MALE) CONNECT TO MIRROR MIRROR (FEMALE) IMAGE Remote Control 1. Power 2. Switch over 3. “+” 4. Menu 5.
Monitor Specifications 7" monitor 5. Menu Down/Volume Down 1. Menu 6. Menu Up/Volume Up 2. Left Arrow 7. Mode 3. Right Arrow 4. Power Screen size 7 inch Aspect ratio 16:9 Resolution 800x480 Brightness 500cdm Audio & Video 4 Ways video input Video System PAL &...
Camera Specifications Sensor 1/4 Sharp Color CCD Resolution (PAL) 582(H)×510(V) pixels TV Line 420 TV Line Lens 2.8mm View angle 150° Power 12-24V Wireless Range 100M @ 2.4Ghz Min illumination 0.1 Lux, infrared night vision Power Consumption Water Resistant IP68 14°F –...
Troubleshooting Monitor Displays Blue Screen & Displays "No Signal" • Do a hard reset, disconnect monitor and camera(s) from power for 1 minute. Reconnect. • Check that the camera is receiving +12VDC and that it has a clean and tight ground connection. •...
In no event shall Buyers Products Company and/or its affiliates have any liability for any losses (whether direct or indirect,...
Page 19
If you have questions about this product, contact: 9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax 800-841-8003 Email: support@buyersproducts.com www.buyersproducts.com IN NO EVENT SHALL SELLER OR MANUFACTURER BE LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES NATURE, LOSSES EXPENSES RESULTING...