Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Expobar PULSE 65
- Page 1 USER MANUAL UM_EN MB27A 05/2018 Original Instructions...
-
Page 2: Table Of Contents
CONTENT NOTIFICATIONS ..............3 Introduction ....................4 Warnings ......................4 Precautions ....................5 Intended use ....................6 OVERVIEW OF COMPONENTS ..........8 DIMENSION SKETCH INSTALLATION AND START-UP ..........9 Positioning ..................... 9 Electrical connection ................... 9 Starting the grinder ..................10 OPERATION ................11 Grinder fneness adjustment .............. -
Page 3: Notifications
NOTIFICATIONS Important: Alerts against unsafe practices. Observe to ensure drink quality, machine performance, food safety, to prevent minor personal injury or damage to the machine. WARNING! Indicates a potentially hazardous situation which, if not avoided, could result in scalding, serious injury and even death. -
Page 4: Introduction
NOTIFICATIONS Introduction Thank you for choosing the EXPOBAR Pulse We hope you enjoy it! Read the user manual before using the This guide refect the current state of machine. the grinder technology and shall not This guide contains important be considered obsolete solely because... -
Page 5: Precautions
NOTIFICATIONS Never insert spoons, forks or other mains cable in water or another liquid. utensils into the pouring lip, or into . Should a foreign object stop the motor, the hopper for any reason whatsoever switch the machine off immediately and while the appliance is operating. -
Page 6: Intended Use
NOTIFICATIONS Before connecting the machine, check The ground wire must be connected; that electrical power supply the electrical system must meet the corresponds to the specifcations on standards set by local safety laws and the data plate. regulations. Should the machine plug not be The machine must be installed by compatible with your socket, have the authorizedandqualifedpersonnel. - Page 7 When this device is activated, do not attempt to operate the machine: isolate the machine from the power supply and eliminate the cause of the problem before re-starting. PULSE 75 DESCRIPTION PULSE 65 HIGH SPEED Voltage (V) 220/240 110/120...
-
Page 8: Overview Of Components
OVERVIEW OF COMPONENTS Hopper lid Bean hopper Grinding adjustment knob Tab to open/close the hopper LCD display Increasing key Decreasing key 1 coffee dose key Manual grinding key 2 coffee doses key Filter folder fork Grinding start key ON/OFF switch... -
Page 9: Dimension Sketch Installation And Start-Up
DIMENSION SKETCH INSTALLATION AND START-UP Positioning 221 mm 554 mm 264 mm MIN. 10 cm Note: Make sure that air is able to circulate behind the machine (minimum 10 cm). The minimum dimensions for the place of the machine must be 230 mm wide x 270 mm depth x 600 mm high. Positionthemachineonafatandstablesurface, awayfromwaterandsourcesofheat. -
Page 10: Starting The Grinder
INSTALLATION AND START-UP Starting the grinder 〱 〲 Insert the hopper into its seat; positioning it so that Tighten the lock screw. the hole lines up with the screw on the back part of grinder. 〳 〴 Remove the cover from the hopper and fll it with Connect the machine to the mains socket and pull the coffee beans. -
Page 11: Operation
INSTALLATION AND START-UP OPERATION Place the flter holder onto the fork and insert it againsttheflterholderrestraint. Note: Dispensing stops once the preset time has elapsed. Note: Theapplianceisequippedwithaflter holder retaining device. 〷 Grinderfnenessadjustment Note: Turn the adjusting knob clockwise to increase grinding fneness or counter-clockwise to increase the grain size. -
Page 12: Filter Holder Fork Height Adjustment
OPERATION CLEANING AND CARE Filter holder fork height adjustment Use a screwdriver to loosen the fastening screw on the flter holderforkItisrecommendednottounscrew the screw completely. Raise or lower the fork in order to adjust it according toflterholderused. Once having set the correct position, tighten the fork fastening screw. -
Page 13: Daily Cleaning - Clean The Dispensing Spout
CLEANING AND CARE Daily cleaning - clean the dispensing spout Clean the dispensing spout using a brush. 〱 Weekly cleaning - bean hopper 〱 〲 Close the hopper by pulling the tab then loosen the Lift the lid and clean with a brush. fastening screw on the side. -
Page 14: Weekly Cleaning - Clean With Grindz
CLEANING AND CARE Weekly cleaning - clean with Grindz 〱 〲 Close the bean stop in bottom of the bean hopper. Start grinder by pressing the ON/OFF switch. Run grinder until no more espresso comes out of the grinder outlet. 2°... -
Page 15: Programming
CLEANING AND CARE PROGRAMMING GrindtwoorthreeservingsofespressotofushthegrinderandoutletofanyremainingGRINDZresidues. Do not use these servings for brewing! Grinder setting 2 coffee doses dispensing time 2 coffee doses icon 1 coffee dose icon 1 coffee dose dispensing time 1 coffee dose counter 2 coffee doses counter Appliance switch-on Note: When switching the appliance on for the... -
Page 16: Manual Mode" Dispensing Mode Activation
PROGRAMMING Note: It’spossibletostoptheautomaticdispensingbeforeit’sfnished thegrindingtime.Duringdispensing,press withtheflterholderthegrindingstartkeytomanuallystopdispensing: Press the grinding start key to resume delivery for the remaining time. Press the dose button (blinking) to stop dispensing. The grinding time returns to the set value. “Manual Mode” dispensing mode activation By pressing the manual mode is activated. - Page 17 For the warranty to be valid, the conditions for maintenance must have been followed in accordance with our instructions, proper care must have been taken and any claim against the warranty must be sent without delay. The equipment in question may not be used while awaiting service if there is any risk that the damage or defect would worsen.
Need help?
Do you have a question about the PULSE 65 and is the answer not in the manual?
Questions and answers