Little Giant DFB30 Quick Start Manual

Disappearing water feature basin

Advertisement

Available languages

Available languages

Franklin Electric Co., Inc.
Oklahoma City, OK 73127
www.lg-outdoor.com
customerservice@lgpc.com

INTRODUCTION

EN
This instruction sheet provides you with the information
required to safely own and operate your Little Giant product.
Retain these instructions for future reference.
The Little Giant product you have purchased is of the highest
quality workmanship and material, and has been engineered
to give you long and reliable service. Little Giant products
are carefully tested, inspected, and packaged to ensure safe
delivery and operation. Please examine your items carefully
to ensure that no damage occurred during shipment. If
damage has occurred, please contact the place of purchase.
They will assist you in replacement or repair, if required.
READ THESE INSTRUCTIONS CAREFULLY BEFORE
ATTEMPTING TO INSTALL, OPERATE, OR SERVICE
YOUR LITTLE GIANT PRODUCT. KNOW THE PRODUCT'S
APPLICATION,
LIMITATIONS,
HAZARDS. PROTECT YOURSELF AND OTHERS BY
OBSERVING ALL SAFETY INFORMATION. FAILURE TO
COMPLY WITH THESE INSTRUCTIONS COULD RESULT
IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!

INSTALLATION (DFB30)

Refer to Figure 1 and the following instructions to install the
DFB30 basin:
1. Dig a hole for the Basin: 30" [76 cm] diameter and 10"
[25.5 cm] deep.
2. Place Basin into hole and verify levelness. Check with
36" level across top rim of basin, checking both left to
right and front to back.
3. If not level, remove Basin and gradually add sand to
areas of hole that need to be raised. Repeat until you
have achieved a level condition.
4. Back-fill with soil all-around the outer perimeter of Basin.
5. Place the Center Support into the Basin, centering it
between the 4 "bumps" molded into Basin floor.
6. Place pump into Basin.
7. Determine the length of tubing required to run from your
pump (on floor of basin), through opening in Center
Support, and up to your fountain.
8. Cut tubing to length, connect one end to pump
discharge fitting. Route through opening in Center
Support, and leave fountain-end disconnected.
9. Install the Top Plate, ensuring orientation of 6" access
hole is over the pump. This will allow easy access to
pump for maintenance.
10. Cover the access hole in Top Plate with provided 6"
diameter access cover, routing the pump's power cord
through open notch of access cover.
11. To complete the installation, please follow the
instructions provided
you purchased.
DISAPPEARING WATER FEATURE BASIN • CUVETTE POUR JEUX
D'EAU EN CIRCUIT FERMÉ • CUBETA PARA FUENTE DE AGUA QUE
AND
POTENTIAL
with the water feature & pump
DESAPARECE

INSTALLATION (DFB36)

Refer to Figure 2 and the following instructions to install the
DFB36 basin:
1. Dig a hole 9" deep, 30" in diameter at the bottom, and
sloping to 35" in diameter at the top. Ensure that the
ground at the bottom is level and solid.
2. Place the basin into the hole, with the power cord cut-out
facing toward the power source.
3. If not level, remove Basin and gradually add sand to
areas of hole that need to be raised. Repeat until you
have achieved a level condition.
4. Back-fill with soil all-around the outer perimeter of Basin.
5. Set the support into the circular receptacle in the center
of the basin and align the tubing cut-outs.
6. Place the pump into the basin, running the power cord
through the cord cut-out.
7. Cut a length of tubing long enough to reach from the
bottom of the basin to the top of the water feature.
8. Run the tubing through the center hole in the top of the
support and out the tubing cut-outs, then connect it to the
pump outlet fitting.
9. Install the six top plates.
10. To complete the installation, please follow the instructions
provided with the water feature & pump you purchased.

INSTALLATION (DFB44)

Refer to Figure 3 and the following instructions to install the
DFB44 basin:
1. Dig a hole 10" deep, 29" square at the bottom, and
sloping to 37" square at the top. Ensure that the ground
at the bottom is level and solid.
2. Place the basin into the hole.
3. If not level, remove Basin and gradually add sand to
areas of hole that need to be raised. Repeat until you
have achieved a level condition.
4. Back-fill with soil all-around the outer perimeter of
Basin.
DFB30
DFB36
DFB44
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DFB30 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Little Giant DFB30

  • Page 1 Little Giant product. DFB36 Retain these instructions for future reference. The Little Giant product you have purchased is of the highest quality workmanship and material, and has been engineered to give you long and reliable service. Little Giant products are carefully tested, inspected, and packaged to ensure safe delivery and operation.
  • Page 2 Support holes Supports (8) Cuvette Trous pour supports Soportes (8) Cubeta Access cover Orificios de soporte Basin Fig. 1 - DFB30 Cuvette Cubeta Cord cut-out Découpe pour cordon Top plates (6) d’alimentation Plaques supérieures (6) Recorte para el cable Placas superiores (6) Fig.
  • Page 3 Consulter la Figure 2 et les instructions suivantes pour consulter plus tard. assembler la cuvette DFB36 : Le produit Little Giant que vous avez acheté a été 1. Creuser un trou rond évasé de 22,8 cm (9 po) de soigneusement fabriqué avec des matériaux de la plus profondeur avec un diamètre de 76,2 cm (30 po) au...
  • Page 4 11. Para completar la instalación, siga los pasos siguientes Little Giant. Guarde las instrucciones para referencia futura. proporcionados en el sistema de agua y la bomba El producto Little Giant que ha adquirido se fabrica adquirida. utilizando mano de obra y materiales de la más alta calidad INSTALACIÓN (DFB36)
  • Page 5 2. Coloque el depósito en el orificio. 3. At its discretion, the Company may inspect products either at its facilities or in the field, and after 3. Si no está nivelado, quite el depósito y agregue arena determination of a warranty claim, will, at its option, gradualmente a las áreas del orificio que necesiten ser repair or replace defective parts.
  • Page 6 FORTH ABOVE, SHALL CONSTITUTE FULFILLMENT OF termes de la garantie qui y sont énoncés. ALL LIABILITY OF THE COMPANY TO THE PURCHASER I. Période de Garantie Applicable WHETHER BASED ON CONTRACT, NEGLIGENCE, OR Les produits accompagnés par cette garantie doivent être OTHERWISE.
  • Page 7 7. Toute utilisation du produit pour laquelle les instructions sans effet, mais le reste de la présente garantie demeurera d’installation et/ou les instructions d’utilisation n’ont pas en vigueur. été suivies. AVIS DE NON-RESPONSABILITE : Les déclarations orales La Société se réserve le droit, à tout moment, et de temps concernant le produit effectuée par le vendeur, la Société, à...
  • Page 8 necesario para, instalar, reparar o remover algún producto. SON AQUÍ EXPLÍCITAMENTE NEGADAS Y EXPRESAMENTE EXCLUIDAS.LA CORRECCIÓN DE DISCONFORMIDAD, DE III. Limitaciones aplicables a esta Garantía Limitada LA MANERA Y EN EL PERÍODO DE TIEMPO ESTABLECIDOS ESTA GARANTÍA NO APLICA A NINGUNO DE LOS ANTERIORMENTE, CONSTITUIRÁ...

This manual is also suitable for:

Dfb36Dfb44

Table of Contents