Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Vaxcel Manuals
  4. Accessories
  5. T0277
  6. Assembly and installation instructions

Vaxcel T0277 Assembly And Installation Instructions

Hide thumbs
1
2
3
4
5

Advertisement

Quick Links

Download this manual
ASSEMBLY AND INSTALLATION
T0277
WARNING:
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
Hardware Package (included):
Mounting Screw X2
Mounting Screw X2
#8/32X1/2 in
#6/32 X1/2 in
Important to Know:
1. If you are not familiar with state and local electrical
codes, it is recommended that you consult with a
qualified electrician.
2. This fixture requires a 120 VAC, 60 Hz power
source.
3. For general safety and to avoid any possible
damage to the sensor, be sure the power is
switched "off" before adjustment.
Maximum Wattage: 22 W
Working Temperature Range: -4
Note: Fixture can be wall mounted or eave mounted.

Wall Mounted

Read notes section on page 4 for additional information about mounting location of fixture.
Light fixture and sensor should be mounted as shown above when installed (depending upon type of installation).
Before installing the light fixture under an eave, the sensor head must be rotated as shown in the next two steps for
proper operation and to avoid the risk of electrical shock.
For eave mounted only:
Rotate the sensor head towards the mounting bracket.
INSTRUCTIONS
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
Mounting Screw X2
Mounting Bracket Screw
#10/24 X1/4 in
0 F ~ 113 0 F
Controls
Mounting Bracket
Mounting Strap
Decorative cover
Features:
1. Energy saving LED fixture.
2. Motion sensor: turns light ON automatically when
motion is detected and turns light OFF automatically
when motion stops.
3. Photocell keeps the light OFF during daylight hours.
4. When in manual override mode, use wall switch
to keep the light ON during the night.
Rotate the sensor head clockwise 180˚ so the controls face down.
Page 1 / 5
Fixture Mounting Screw
Eave Mounted
Controls
Wire Connector X3
Controls
160729

Advertisement

loading

Related Manuals for Vaxcel T0277

Summary of Contents for Vaxcel T0277

  • Page 1: Wall Mounted

    ASSEMBLY AND INSTALLATION INSTRUCTIONS T0277 WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS.

  • Page 2: Installation Steps

    Mounting Bracket Screw Wire Connector Decorative cover FRONT Back Plate Outlet Box Light Head Mounting Bracket Sensor Installation Steps Mounting Strap Turn off the power at fuse or circuit box. Fig. 1 1. The mounting bracket is pre-assembled on the light fixture. Unscrew the decorative cover, fixture mounting screw in order to remove the mounting bracket.

  • Page 3: Adjusting The Light Head

    2. You can rotate the sensor head up and down to change the coverage area. (See Fig. 2) Walk through the detection zone at the farthest distance you wish to detect motion. Note: Range set too high may increase false triggering. (See Fig. 3 and Fig. 4) Fig.

  • Page 4: Troubleshooting

    Customization Options: Shut-off Delay FIG.7 (View from Bottom of Sensor) ● The shut-off delay is the length of time the light will stay at brightness after motion has ceased to be detected. ● You can set the shut-off delay by rotating the delay time knob arrow so it points to the desired time setting within “TIME”...

  • Page 5: Year Limited Warranty

    The following parts are available for re-order if damaged or missing. Spare Parts List: Mounting Screw X2 Mounting Screw X2 Mounting Screw X2 Mounting Strap Mounting Bracket Screw Decorative cover Fixture Mounting Screw Wire Connector X3 #8/32X1/2 in #6/32 X1/2 in #10/24 X1/4 in Assembly Kit 5076MM...