Tresco KVF-12030-TDW Installation Instructions

LED 12VDC Power Supply (30W)
LED 12VDC Power Supply (60W)
Mounting Block included with each Power Supply.
For best operation, use LED-compatible wall dimmers.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: To reduce the risk of fire, electric shock, or injury to persons:
Read all instructions before installing system.
Before beginning installation, be sure power is turned OFF to the
power supply and light system.
• The 30W Power Supply operates on line voltage 100-277 VAC.
The 60W Power Supply operates on line voltage 100-277 VAC.
Shock Hazard: Whenever hardwiring the LED Power Supply to a
120-volt circuit with an AC dimmer, turn off power at the circuit breaker
before installing. Failure to do so may result in serious personal injury
or death.
Warning: All wiring must be in accordance with national and local
electrical codes, low-voltage Class 2 circuit. The Power Supply is to
be mounted and wired in accordance with Article 450 of the National
Electric Code (NEC). Failure to install the Power Supply and light fixture
in compliance with applicable codes and regulations may cause serious
personal injury, death and/or major property damage.
• The Power Supply must be installed in a well-ventilated area free
from explosive gases and vapors. Do not install in an airtight, boxed-
in structure. The Power Supply is cooled by circulating air and by
mounting the unit flush to a surface to allow for heat transfer. Operate
Derating Curve
100
80
60
40
20
-40 -20 0 10 20 30 40 50 60 70
Ambient Temperature (°C)

Technical Specifications

Part No. L-DCE30D-CON
Output: LED DC Power Supply (30W)
DC Voltage 12V
L-DCE30D-CON
Rated Current 2.5A
Rated Power 30W max.
Minimum Load 3W
Input:
Voltage Range 100-277VAC
Frequency Range 47-63Hz
Power Factor 0.99@120VAC
0.98@277VAC
(Typ.) @ full load
Efficiency 79%
(Typ.) @ full load
LED DC Power Supply (60W)
Wiring Suitable for 18-14 AWG, rated 300V, min. 90°C
L-DCE60D-CON
Protection:
Short Circuit Shut down o/p voltage, re-power on to recover after fault
condition is removed
≤
Over Loading 120% shut down o/p
voltage, re-power on to
recover
Over Temperature 100°C ± 10°C shut down o/p voltage, automatically
recover after cooling
Working Temperature -40°C ~ +60°C
Model: ............ KVF-12030-TDW
Part No: ........... L-DCE30D-CON
Model: ............ KVF-12060-TDW
Part No: ........... L-DCE60D-CON
Line Voltage Input Cord
Neutral (white wire)
Ground (green wire)
Line (black wire)
L-DCE60D-CON
LED DC Power Supply (30W)
12V
L-DCE30D-CON
5A
60W max.
6W
100-277VAC
47-63Hz
LED DC Power Supply (60W)
L-DCE60D-CON
0.98@120VAC
0.95@277VAC
83%
≤
120% Hiccup mode, recovers
automatically after fault
condition is removed
(see Derating Curve chart above)
Hardwire LED Power Supplies
Class 2 • Dimmable 30W & 60W 12VDC Constant Voltage
the Power Supply at cooler surrounding air temperatures to extend
the life of the unit. See Derating Curve for temperatures above 40°C
(104°F).
• Operate only within the specified ambient temperature range of -40°C
(-40°F) to 60°C (140°F).
Note: It is normal for the LED Power Supply to feel warm when under
a full wattage load.
• The hardwired installation of the Power Supply should only be
performed by a qualified electrician.
• Do not conceal the line voltage input cord or Power Supply inside a
wall, ceiling, soffit, or similar permanent structure, unless consulting
a licensed electrician. This requirement does not apply to the 12VDC
wiring between the Power Supply and the cabinet light system. For
wire runs inside a wall, ceiling, soffit, or similar permanent structure,
use CL2 or better cabling.
• Do not install low-voltage Class 2 wiring along the same run as AC line
voltage. If the line voltage and low-voltage wires need to cross, keep
them at 90° angles.
• Use only insulated staples or plastic ties to secure ALL loose wires.
• Route and secure wires so that they will not be pinched or damaged
when the cabinet is pushed to the wall.
Typical Application
LED Wall Dimmer
Line Voltage Input Cord
Install Wall Dimmer on
Neutral (white wire)
LED Wall Dimmer
Ground (green wire)
input (line voltage) side
LED Power Supply
Line (black wire)
of Power Supply
12VDC, 30W or 60W
Install Wall Dimmer on
input (line voltage) side
of Power Supply
LED DC Power Supply (30W)
L-DCE30D-CON
20 mm
13/16 in.
54 mm
2-1/8 in.
LED DC Power Supply (60W)
L-DCE60D-CON
24 mm
15/16 in.
61 mm
2-3/8 in.

Installation Instructions

OUTPUT 12VDC
L Black Red
N White Black
INPUT
OUTPUT 12VDC
L Black Red
N White
Black
INPUT
LED Power Supply
12VDC, 30W or 60W
20 mm
13/16 in.
155 mm
54 mm
6-1/8 in.
2-1/8 in.
155 mm
6-1/8 in.
24 mm
15/16 in.
61 mm
2-3/8 in.
178 mm
7 in.
(Continued on page 2)
Mounting Block
Mounting Block
Mounting Block
pre-wired to Power Supply
13 mm
1/2 in.
26 mm
1 in.
26 mm
88 mm
1 in.
3-7/16 in.
88 mm
3-7/16 in.
Cord
102 mm
4 in.
Cord
152 mm
6 in.
178 mm
7 in.
Page 1