Advertisement
Quick Links
TM
PRO POOL
UPGRADE KIT
PART NUMBER: F-004PLBAP
INSTALLATION INSTRUCTIONS
MANDATORY – LEAVE THIS MANUAL WITH LIFT OWNER
- WARNING-
IMPORTANT SAFETY INSTRUCTIONS
1. READ AND FOLLOW ALL INSTRUCTIONS. LIFT SAFETY CAN ONLY BE ENSURED IF THE
LIFT IS INSTALLED AND OPERATED PROPERLY – ACCORDING TO THESE INSTRUCTIONS.
2. TO REDUCE THE RISK OF INJURY, DO NOT PERMIT CHILDREN TO USE THIS PRODUCT
UNLESS THEY ARE CLOSELY SUPERVISED AT ALL TIMES.
3. DO NOT PERMIT CHILDREN TO PLAY ON OR AROUND THIS PRODUCT.
4. NEVER APPLY DIRECT WATER PRESSURE TO THE ELECTRONIC COMPONENTS.
5. SAVE A COPY OF THESE INSTRUCTIONS IN A SAFE AND EASILY ACCESSIBLE PLACE.
AQUA CREEK PRODUCTS
9889 GARRYMORE LANE
MISSOULA, MT 59808
1-888-687-3552
FAX: 406-549-2602
FEB 2012
©2012 AQUA CREEK PRODUCTS, LLC
1
Advertisement
Summary of Contents for Aqua Creek Products PRO POOL F-004PLBAP
- Page 1 4. NEVER APPLY DIRECT WATER PRESSURE TO THE ELECTRONIC COMPONENTS. 5. SAVE A COPY OF THESE INSTRUCTIONS IN A SAFE AND EASILY ACCESSIBLE PLACE. AQUA CREEK PRODUCTS 9889 GARRYMORE LANE MISSOULA, MT 59808 1-888-687-3552 FAX: 406-549-2602 FEB 2012 ©2012 AQUA CREEK PRODUCTS, LLC...
- Page 2 ) battery allows one battery to always be on the charger, and the chest straps provide additional security for special needs. Use the Transport Cart to make moving and storage easier. The instructions on the following pages show how to install and use these accessories to maximum advantage. ©2012 AQUA CREEK PRODUCTS, LLC...
- Page 3 The Pro Pool Cover fits over the lift, and has grommet holes to allow for locking it. The photo shows the lift with the cover installed. COVER IS OVER THE LIFT; USE THE DRAW-STRING TO TIGHTEN ©2012 AQUA CREEK PRODUCTS, LLC...
- Page 4 The headrest pad is also removable for cleaning. Look over the diagram below to familiarize yourself with the components before installing and using the HEADREST ASSEMBLY. ©2012 AQUA CREEK PRODUCTS, LLC...
- Page 5 HEADREST PAD. When installing the pad thread the bracket through the middle loop first and slide the pad up to the top loops. Thread the bracket through the top loops (one at a time) to complete the installation. To remove the pad, reverse this procedure. ©2012 AQUA CREEK PRODUCTS, LLC...
- Page 6 ASSEMBLY is now ready to adjust and use. NOTE: The INTEGRATED HEADREST ASSEMBLY will work on all 2 generation 18” wide Aqua Creek Products’ chairs*. The 18” chair comes standard on all Aqua Creek Products’ Scout , Ranger , Pro Pool and Patriot pool lifts.
- Page 7 Remove the ¼” x 1” button-head cap screws and washers from the back of the chair and use them to install the chest strap as shown below. The chest strap is fastened with hooks & loops, so make sure they face each other when the straps are installed. ©2012 AQUA CREEK PRODUCTS, LLC...
- Page 8 CHARGE light will GO OFF and the battery is ready to use The battery charger will automatically shut off when the battery is fully charged, so the battery can stay on the charger any time it is not being used. ©2012 AQUA CREEK PRODUCTS, LLC...
-
Page 9: Battery Maintenance
Scotch Brite or any similar product. Clean off any corrosion or discoloration on the very top surfaces of the battery contacts and then apply dielectric grease (supplied with lift) as shown in the figure below. ©2012 AQUA CREEK PRODUCTS, LLC... - Page 10 To use the Transport Cart the lift must be removed from the anchors. Remove the ½” bolts with a 9/16” wrench or socket. The Transport slides under the baseplate as shown in the photo at the bottom of the page. ©2012 AQUA CREEK PRODUCTS, LLC...
Need help?
Do you have a question about the PRO POOL F-004PLBAP and is the answer not in the manual?
Questions and answers