Summary of Contents for Carlisle Binks 31-397
- Page 1 SERVICE MANUAL 15:1 GEAR DRIVEN AIR MOTOR DRIVES AND AGITATOR ASSEMBLIES FOR OPEN AND CLOSED DRUMS AND LARGE TANK ASSEMBLIES 31-451 31-424 31-454 77-3139-R2 (1/2019) 1 / 12 www.carlisleft.com...
- Page 2 In this part sheet, the words WARNING, CAUTION and NOTE are used to emphasize important safety information as follows: WARNING NOTE CAUTION Hazards or unsafe practices which Hazards or unsafe practices which could result in severe personal Important installation, operation or could result in minor personal injury, injury, death or substantial property maintenance information.
-
Page 3: Pressure Relief Procedure
DESCRIPTIONS 15:1 GEAR DRIVEN AGITATORS FOR 55 GALLON OPEN TOP DRUMS: 31-424 55 Gallon Agitator with Stainless Steel Drum Cover 31-397 55 Gallon Agitator with Plated Steel Drum Cover 31-400 Gear Driven Agitator Assembly (less cover) 31-456 Agitator Drive for 31-423, 31-397, and 31-400 41-3305 Agitator only (less drive and less cover) 31-455... - Page 4 55 GALLON AGITATORS WITH 15:1 GEAR REDUCTION FOR OPEN TOP DRUMS 55 GALLON AGITATORS 15:1 AGITATOR DRIVE 31-397 with plated steel cover (shown) 31-455 with Air Hose/fittings (shown) 31-424 with stainless steel cover 31-456 less Air Hose/fitting 31-400 Agitator (no cover) 41-3305 (no drive or cover) (items 3-11) 83-2114 STUFFING BOX ASSEMBLY (Item 4)
- Page 5 55 GALLON AGITATOR AND 55 GALLON AGITATOR AND 15:1 AGITATOR 15:1 AGITATOR DRIVE PARTS LIST DRIVE INSTALLATION INSTRUCTIONS Ind. Ref. Replacement WARNING Description Parts Part No. Req'd. 15:1 AGITATOR DRIVE (INCLUDED WITH 31-452 Before attempting any installation of agitators onto 31-397, 31-400, 31-424) pressurized tanks, the tanks must be relieved of pressure 15:1 AGITATOR DRIVE...
- Page 6 AGITATOR DRIVE UNITS FOR AGITATOR EQUIPPED DRUMS 31-451 AGITATOR DRIVE 31-453 DRIVE UNIT FOR 31-454 31-454 AGITATOR DRIVE www.carlisleft.com 6 / 12 77-3139-R2 (1/2019)
- Page 7 AGITATOR DRIVE UNITS PARTS LISTS 31-451 DRIVE UNIT ASSEMBLY 31-453 DRIVE UNIT ASSEMBLY ITEM ITEM PART NO. DESCRIPTION QTY. PART NO. DESCRIPTION QTY. 350-401 MUFFLER & AIR STRAINER ASSEMBLY 350-401 MUFFLER & AIR STRAINER ASSEMBLY STRAINER CAP STRAINER CAP SCREEN SCREEN ▲...
-
Page 8: Installation Instructions
31-453 & 31-454 31-451 INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 1. Loosen cap screw (64) and separate the gear-motor (47) 1. Adapter (56) has two thread sizes: 1-1/2” NPS (m) on one from the coupling adapter (63). end and 2” NPS(m) on the other end. Choose the proper thread size and place the adapter over the agitator shaft of 2. - Page 9 BASE DRIVE UNIT 31-434 15:1 GEAR REDUCTION DRIVE ASSEMBLY 31-434 GEAR REDUCTION DRIVE 31-434 PARTS LIST ITEM PART NO. DESCRIPTION QTY. AIR MOTOR WITH COUPLING 31-437-K (INCL W/ 31-434) 20-6990 COUPLING ASSEMBLY 20-1068 COUPLING SPIDER Purchase Locally SET SCREW, 1/4-20 X 5/16" 31-422 COVER PLATE (INCL W/ 31-435-K) Purchase Locally...
-
Page 10: Gearbox Oil
AIR MOTOR DRIVE SERVICE CHECKS CONDITION CAUSE CORRECTION Clean or replace the felt (43). Air motor muffler (40) is clogged. Replace muffler (40) if necessary. Lubricate (see "Air Motor Lubrication" Air motor needs lubrication or cleaning. section). Disassemble and clean per parts replacement instructions. - Page 11 15:1 AGITATOR DRIVE FLEX COUPLING INSTALLATION Assemble one coupling jaw from the coupling assembly (81) onto the air motor shaft (80). Make sure to keep the coupling face flush with the end of the motor shaft as shown. Apply Loctite 243 (or equivalent) to set screw threads. Align the set screw to motor shaft flat and tighten.
-
Page 12: Warranty Policy
This product is covered by Carlisle Fluid Technologies’ materials and workmanship limited warranty. The use of any parts or accessories, from a source other than Carlisle Fluid Technologies, will void all warranties. Failure to reasonably follow any maintenance guidance provided may invalidate any warranty.