Page 2
GH08 iTouch Prologue Thank you for choosing to buy our GH08 Series Sauna heater, please take the time to read these instructions before you begin as they contain important information about the installation and maintenance requirements. GH08 Series Sauna heaters are available in specifications from 9kw to 18kw and are equipped with our iTouch digital controller &...
Page 3
iTouch GH08 Circuit Diagram for sauna heater and control Box Parts Description Heat element Heating Shell Insulate the inner shell to prevent from scalding Cover Panel Cover the electrical parts Terminal Connect the power supply Power entry The route of power wires Page 2...
Page 4
GH08 iTouch Circuit Diagram for sauna heater and control Box Figure: 1A GH08 9KW Heating Element Figure: 1B Heating Element GH08 18KW Page 3...
Page 6
GH08 iTouch Parameter and size of sauna heater Table: 1 Heater Input Heating element Sauna room Voltage Phase P Connecting Stones kg Size mm model n×KW volume cable n×mm min max GH08 6×1.5 5 - 7 230 /400 1/3N Terminal1: L:480 40~50 (H1-H6)
iTouch GH08 Installation Important Prior to installing sauna heater, please refer to Installation handbook and check it as following ● points: Is the output power and type of the heater suitable for the Sauna Room? See parameter table 1 ● (Technical parameter) on page 5.
GH08 iTouch Heater Guard (not supplied) The heater should be guarded against accidental contact with a wooden guard similar to the one shown below – according to the position of the heater within the cabin it may need to be guarded on 2 or 3 sides.
Page 10
GH08 iTouch Picture 2: Real Time Clock After Power Of Picture 3: Bluetooth Music Picture 4: Light Picture 5: User Mode Picture 6: Settings Picture 7: Presetting Power On Picture 8: Real Time Setting Picture 8: Temperature Setting Page 9...
iTouch GH08 Control Panel Installation Important: The control panel must be installed outside the sauna room. The control panel can be installed at ● switch height, but the temperature sensor must be installed at 1.8m from FFL inside the sauna room. A.
GH08 iTouch Control Panel Dimensions Without Expansion Bracket With Expansion Bracket Page 11...
Page 13
iTouch GH08 Operation Instructions 1. Power On When the system is electrify, you will hear a “BEEP “sound from the control panel. ● The sauna system is now in standby mode as per image below. ● Time will only display in standby mode once the clock has been set. Otherwise only a blank screen ●...
Page 14
GH08 iTouch 3. Light Power On When the system is in working mode, press the button to enter the light interface as ● displayed below. Press the button to power on the light. ● Press the button to power off the light. ●...
iTouch GH08 Temperature setting: When the sauna function is active, press button with the symbol between them, ● to set steam temperature, TEMP range is 25-68°C and increases or decreases in increments of 1°C. ● Sauna Run Time setting: When the sauna function is active, press the button with the symbol ●...
GH08 iTouch Auto On Timer Function: Enter the settings interface below by pressing the button. ● When system is in setting interface as in image above, select ”work mode” column, ● press to enter the interface as displayed below. Time Setting Move the arrow to the “Timing”...
Page 17
iTouch GH08 Real clock When the system is in the settings interface as in image above, Select the “Real Time” column ● by pressing the button. Press the button to enter the interface in the image below. ● Press button to move arrow to the data you like to set, such as hour, minute, date, ●...
GH08 iTouch Bluetooth Music: Open Bluetooth on your mobile device select the “SANJUN-MUSIC” Bluetooth device. ● Enter password “0000" to complete the pairing process. Select “SANJUN-MUSIC” as your ● audio output on your mobile device. Open you playlist ● Select the Bluetooth interface as show in image above by pressing the button .
iTouch GH08 Trouble Shooting When there is an error detected by the system, the system will display an error code. Error Code Description Trouble Shooting Temperature sensor open circuit Please check the temperature sensor cable, if there are no loose connections, please replace the temperature sensor.
GH08 iTouch Maintenance We recommend that you inspect the sauna heater on a regular basis for any signs of deterioration of the condition, pay particular attention to both the fastenings, the condition of the wiring and the electrical elements. Note if the rocks have started to crumble this can cause the elements to overheat and they should be changed for new rocks.
Need help?
Do you have a question about the iTouch GH08 Series and is the answer not in the manual?
Questions and answers