Related Manuals for RHEINTACHO qbLED
Summary of Contents for RHEINTACHO qbLED
- Page 1 Operating instructions RHEINTACHO TUTORIAL Stroboscope RT STROBE qbLED Stroboscope RT STROBE qbLEDs* Stroboscope RT STROBE super qbLED * Stationary version without integrated battery and without handle...
-
Page 2: Complete Overview Of Connections, Controls And Settings
Store / read parameters (MEMORY IN / MEMORY OUT) (12) Pro mode (P) (13) Battery status – full, half full or low (6) (7) (8) (9) (10) (11) (12) (13) Fig. 2: Display Operating instructions RT STROBE qbLED / RT STROBE qbLEDs / RT STROBE super qbLED... -
Page 3: Table Of Contents
7.2.3 Pro mode (Fig. 2) 7.2.4 Stroboscope super qbLED (Fig. 2) 7.2.5 Operating mode Factory reset Accessories, optional Determining the actual rotational speed of an object Operating instructions RT STROBE qbLED / RT STROBE qbLEDs / RT STROBE super qbLED... -
Page 4: Technical Data
1,050 g approx. 1,150 g Ambient conditions qbLEDs qbLED super qbLED Temperature 0 - 40 °C / 32 - 104 °F Type of protection IP30 Operating instructions RT STROBE qbLED / RT STROBE qbLEDs / RT STROBE super qbLED... -
Page 5: About These Operating Instructions
(version qbLEDs) for the device (version qbLEDs) (B) INPUT Input socket Input for external trigger / 24 V power supply for sensor Operating instructions RT STROBE qbLED / RT STROBE qbLEDs / RT STROBE super qbLED... -
Page 6: Brief Description Of Set-Up Steps
The device must be manually switched between external and internal trigger signals (see section 7.2.2 “Standard mode / How to select an internal / external trigger”). Operating instructions RT STROBE qbLED / RT STROBE qbLEDs / RT STROBE super qbLED... -
Page 7: Standard Mode (Fig. 2)
This setting is not affected by the current rotational speed, which means that the stroboscope will flash at the desired position even during rotational speed fluctuations or during the start-up period. Operating instructions RT STROBE qbLED / RT STROBE qbLEDs / RT STROBE super qbLED... -
Page 8: Pro Mode (Fig. 2)
"external trigger" is selected. Note SLOW (slow motion) See also section 7.2.2 "Standard mode" for examples and explanations regarding above mentioned display messages. The “SLOW” function allows the viewer to view movement in slow motion. The speed of the slow motion depends on the flash frequency and corresponds to the value selected. Operating instructions RT STROBE qbLED / RT STROBE qbLEDs / RT STROBE super qbLED... -
Page 9: Stroboscope Super Qbled (Fig. 2)
7.3 Factory reset LASER The trigger frequency is below the measurement range. Note To reset the factory settings, press and hold the rotary/push knob (D) for at least 5 seconds. Operating instructions RT STROBE qbLED / RT STROBE qbLEDs / RT STROBE super qbLED... -
Page 10: Accessories, Optional
Printed CE declaration of conformity is available on request. Subject to technical changes without prior notification. Although the content of these instructions was compiled with the greatest care, we cannot accept liability for any errors. Operating instructions RT STROBE qbLED / RT STROBE qbLEDs / RT STROBE super qbLED... - Page 11 Notes Operating instructions RT STROBE qbLED / RT STROBE qbLEDs / RT STROBE super qbLED...
- Page 12 RHEINTACHO Messtechnik GmbH RHEINTACHO Vision Systems S.A.S. Waltershofener Straße 1 18, Rue de la Fabrique 79111 Freiburg · Germany 68530 Buhl · France Tel: +49 (0)761 45 13 0 Tel: +33 (0)3 89 83 06 82 Fax: +49 (0)761 44 52 74 Fax: +33 (0)3 89 83 07 43 info@rheintacho.de...
Need help?
Do you have a question about the qbLED and is the answer not in the manual?
Questions and answers