Related Manuals for Hiniker VERSAPLOW 4208
Summary of Contents for Hiniker VERSAPLOW 4208
- Page 1 SKID STEER LOADER VERSAPLOW MODELS 4208, 4210 OPERATOR’S MANUAL DO NOT USE OR OPERATE THIS EQUIPMENT UNTIL THIS MANUAL HAS BEEN READ AND THOROUGHLY UNDERSTOOD PART NUMBER 27000355...
-
Page 3: Table Of Contents
Table of Contents TABLE OF CONTENTS 27000355 9/19 MANUALS/27000355 TO THE PURCHASER ........................2 SAFETY ............................3 OPERATING PROCEDURES ....................4-8 MAINTENANCE ........................9-10 TROUBLE SHOOTING ........................11 VERSAPLOW ASSEMBLY ..................... 12-15 SPECIFICATIONS ........................16 WIRING DIAGRAM ........................17 HYDRAULIC DIAGRAMS ......................18 ELECTRICAL PIN LAYOUT ...................... -
Page 4: To The Purchaser
To The Purchaser TO THE PURCHASER This product is designed and manufactured to All references to Left or Right are defined as give years of dependable service when properly viewing the plow from the cab of the machine. maintained and used for the purpose for which it is intended. -
Page 5: Safety
Safety SAFETY This is a safety alert symbol. It alerts BEFORE OPERATION an operator to information concerning personal safety. Always observe Discipline yourself to visually check for and heed these symbols and instructions, worn, damaged or cracked parts before otherwise death or serious injury can result. starting use. -
Page 6: Operating Procedures
4 Operating Procedures OPERATING PROCEDURES IMPORTANT: To prevent damage to When using a 7 or 14 pin harness that operates snowplow components, skid steer the plow through the base machines internal loaders with a “High Flow/Low Flow” controls operators need to push and hold the hydraulic system must be operated in the joystick button specifi... - Page 7 Operating Procedures 5 TRANSPORTING PLOW Raise plow to a position where it does not block your view forward. Transport plow with hydraulic flow off or in neutral to prevent accidental lowering of plow. Never adjust blade position while driving. PLOWING SNOW WARNING: Always wear seat belt and lower seat bar, if equipped, when plowing snow.
- Page 8 6 Operating Procedures DWG NO. 7608 DWG NO. 7745 Clear large lots by angling blade and creating a Slowly back drag snow away from parking stall single path. Push snow to outer edges of lot by or building to an open area. taking successive passes with blade angled.
- Page 9 Operating Procedures 7 HITCH OPTIONS There are (2) hitch options for the VersaPlow, fixed and floating. DWG NO. 7750 This hitch is recommended for front wheel drive and some 4 wheel drive vehicles where slight down pressure on plow can cause operators to DWG NO.
-
Page 10: Operating Procedures
8 Operating Procedures ADJUSTING OUTER CUTTING EDGES REMOVING PLOW Park the plow on a solid level surface with the Periodically after finishing snowplowing check height of box end urethane cutting edges in blade straight across the loader. both push and back drag mode with respect to main cutting edge. -
Page 11: Maintenance
Maintenance 9 Section MAINTENANCE TITLE WARNING: Do not service or otherwise GRADE 5 TYPE B & F LOCK NUT TORQUES handle a plow in the raised position unless it is securely blocked against Size Ft-lbs. unexpected falling. 5/16” 13-18 17-25 3/8”... -
Page 12: Maintenance
Maintenance ELECTRICAL MAINTENANCE Periodically check all electrical connections for proper fi t and remove any contamination, that may be present. To prevent contamination, always place dust caps on connectors when not in use. This is particularly important when the plow is being stored. The use of dielectric grease is recommended to reduce corrosion of the contacts and to make connecting and disconnecting easier. -
Page 13: Trouble Shooting
Trouble Shooting 11 Section TROUBLE SHOOTING TITLE GENERAL Check the hydraulic oil level in the skid Check to see that the plow and loader are steer loader. wired correctly with clean, tight connections at the battery. Check for proper voltage. Check for external leakage at cylinders, hoses and valve manifold. - Page 14 VersaPlow Assembly Section VERSAPLOW ASSEMBLY TITLE GENERAL INFORMATION Insert main pivot pin so formed lip is pointing rearward. Slide the washer onto the bottom WARNING: To prevent personal injury of the pin, then secure the assembly with or death, be certain to keep clear of any the slotted nut and cotter pin.
-
Page 15: Versaplow Assembly 13
VersaPlow Assembly 13 When installing a Versa Plow with the ocillating/fl oating hitch option on a loader with with taller snow tires, remove and reinstall two rear push frame bolts through the upper set of holes to allow more downward travel of the blade. Oscillating Hitch Hose Routing DWG NO. - Page 16 VersaPlow Assembly Attach two leveling bars onto the ribs using IMPORTANT: Damage to the wiring provided 5/16 hardware. harness will occur if adequate cable length is not provided to allow for full motion of the loader arms. Use plastic tie straps to secure the wiring harness to the loader arm immediately adjacent to the loader arm pivot point.
- Page 17 VersaPlow Assembly 15 Refer to Operating Procedures section for ADJUSTING OUTER CUTTING EDGES attaching and operating the plow. Test that all functions are working properly and that cabling Check height of box end urethane cutting edges is not being stretched or pinched. in both push and back drag mode with respect to main cutting edge.
-
Page 18: Specifications
Section Specifications SPECIFICATIONS TITLE Models 4108 4208 4110 4210 Blade Width 8’ 8’ 10’ 10’ Overall Width 8’ 8” 8’ 8” 10’ 8” 10’ 8” Blade Height 30 1/2” 30 1/2” 30 1/2” 30 1/2” Weight 807 lbs. 938 lbs. 911 lbs. -
Page 19: Wiring Diagram
Wiring Diagram 17 Section UNIVERSAL CONTROLLER WIRING DIAGRAM TITLE DWG NO. 4286... -
Page 20: 18 Hydraulic Diagrams
18 Hydraulic Diagrams DWG NO. 7618... -
Page 21: Electrical Pin Layout 19
Electrical Pin Layout 19 Skid Steer Electronic Pin Layout Bobcat 14 Pin LH L/R (-) Gnd LH Center L LH Center R Case 14 Pin (-) Gnd Button 2 LH Handle Dn Button 2 LH Handle Up Cat 14 Pin LH Trigger Aux 7 (-) Gnd C-Control Aux 5... - Page 22 20 Notes NOTES:...
-
Page 23: Warranty 21
Any improper use, operation beyond rated capacity, substitution of parts not approved by Hiniker, or any alteration or repair in such manner as in our judgment affects the product materially and adversely shall void this warranty.
Need help?
Do you have a question about the VERSAPLOW 4208 and is the answer not in the manual?
Questions and answers