AEL VALIANT Series Installation Instructions

INSTALLATION INSTRUCTIONS
VALIANT SERIES POST TOP
DISCONNECT POWER BEFORE RELAMPING OR WIRING THE FIXTURE.
HOUSING MUST BE GROUNDED TO REDUCE POTENTIAL OF ELECTRICAL SHOCK
READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION
RISK OF FIRE. PRODUCT FOR OUTDOOR INSTALLATION AND USE ONLY.
TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL
APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. FOR CODE INTERPRETATION,
!
CUPOLA LENS CUPOLA LENS
ADJUST PHOTO- ADJUST PHOTO-
CONTROL BY LIFTING CONTROL BY LIFTING
& TURNING CUPOLA & TURNING CUPOLA
SIMULTANEOUSLY SIMULTANEOUSLY
HOOD HOOD
TRIGGER TRIGGER
LATCH (2) LATCH (2)
-OPTIONAL- -OPTIONAL-
LENS LENS
PANELS (4) PANELS (4)
NEMA NEMA
LABEL HERE LABEL HERE
-OPTIONAL- -OPTIONAL-
LADDER REST (2) LADDER REST (2)
-OPTIONAL- -OPTIONAL-
SET SCREWS (3) SET SCREWS (3)
FIGURE 1 FIGURE 1
CLOSED HOOD - STREET SIDE VIEW CLOSED HOOD - STREET SIDE VIEW
LAMP LAMP
SOCKET SOCKET
"STREET "STREET
SIDE" SIDE"
LABEL LABEL
LENS LENS
PANELS (4) PANELS (4)
FIGURE 2 FIGURE 2
OPEN HOOD - TOP VIEW OPEN HOOD - TOP VIEW
DRAWING NO. A67959 REV C
American Electric Lighting a division of Acuity Lighting Group, Inc. Newark, OH
TM
CONSULT LOCAL CODE AUTHORITY
CAUTION
LIFT UNIT OUT OF BOX BY BAG, NOT CUPOLA
CUPOLA CAP CUPOLA CAP
CUPOLA BASE CUPOLA BASE
CLOSURE CLOSURE
SCREW SCREW
BOSS (2) BOSS (2)
SCREW NOT SCREW NOT
SHOWN SHOWN
LOWER HOUSING LOWER HOUSING
MIN POLE OD 2.375" MIN POLE OD 2.375"
MAX POLE OD 3" MAX POLE OD 3"
POWER POWER
PAD PAD
LOWER LOWER
HOUSING HOUSING
CAPTIVE CAPTIVE
SCREW FOR SCREW FOR
POWER PAD (4) POWER PAD (4)
©2008 ACUITY LIGHTING GROUP, INC.
(FRONT)
WARNING
!
WARNING
!
CAUTION
!
OPENING & CLOSING THE UNIT: OPENING & CLOSING THE UNIT:
1 1 . . TO OPEN THE FIXTURE, LOCATE THE TWO CLOSURE SCREWS. TO OPEN THE FIXTURE, LOCATE THE TWO CLOSURE SCREWS.
THESE ARE LOCATED ON TWO ROUND BOSSES ON THE THESE ARE LOCATED ON TWO ROUND BOSSES ON THE
STREET SIDE OF THE FIXTURE. (SEE FIGURE 1.) STREET SIDE OF THE FIXTURE. (SEE FIGURE 1.)
2. UNSCREW THE TWO CAPTIVE CLOSURE SCREWS. YOU WILL 2. UNSCREW THE TWO CAPTIVE CLOSURE SCREWS. YOU WILL
KNOW KNOW T THE SCREWS ARE COMPLETELY DISENGAGED FROM HE SCREWS ARE COMPLETELY DISENGAGED FROM
THE HOOD WHEN THE HOOD WHEN THE SCREWS CAN MOVE FREELY UP AND
DOWN. DOWN.
3. OPEN THE HOOD. 3. OPEN THE HOOD.
4. TO CLOSE THE FIXTURE, SIMPLY CLOSE THE 4. TO CLOSE THE FIXTURE, SIMPLY CLOSE THE HOOD AND RE-
TIGHTEN THE TWO CAPTIVE CLOSURE SCREWS. TIGHTEN THE TWO CAPTIVE CLOSURE SCREWS.
NOTE FOR OPTIONAL TRIGGER LATCH: TO OPEN THE UNIT NOTE FOR OPTIONAL
SIMPLY PULL BOTH TRIGGERS SIMULTANEOUSLY WITH YOU SIMPLY PULL BOTH TRIGGERS SIMULTANEOUSLY WITH YOUR R
INDEX FINGER WHILE PUSHING UP ON THE HOOD WITH YOUR INDEX FINGER WHILE
THUMBS. CLOSE THE UNIT BY CLOSING THE HOOD AND PRESSING THUMBS. CLOSE THE UNIT BY
DOWN UNTIL THE TRIGGER LATCHES ENGAGE. DOWN UNTIL THE TRIGGER LATCHES ENGAGE.
POWERPAD REMOVAL & INSTALLATION: POWERPAD REMOVAL & INSTALLATION:
1. OPEN THE UNIT. (SEE "OPENING AND CLOSING THE UNIT" 1. OPEN THE UNIT. (SEE "OPENING AND CLOSING THE UNIT"
ABOVE.) ABOVE.)
2. UNSCREW THE FOUR CAPTIVE SCREWS ATTACHING THE 2. UNSCREW THE FOUR CAPTIVE SCREWS ATTACHING THE
POWER PAD TO THE UNIT, TOTALLY DISENGAGING THEM POWER PAD TO THE UNIT, TOTALLY DISENGAGING THEM
FROM THE CASTING. (SEE FIGURE 2). YOU WILL KNOW THE FROM THE CASTING. (SEE FIGURE 2). YOU WILL KNOW THE
SCREWS CAN MOVE FREELY UP AND DOWN. SCREWS CAN MOVE FREELY UP AND DOWN.
3. GRIPPING THE LAMP SOCKET & BRACKET, REMOVE THE 3. GRIPPING THE LAMP SOCKET & BRACKET, REMOVE THE
POWER PAD FROM THE UNIT, DISCONNECTING THE WIRING POWER PAD FROM THE UNIT, DISCONNECTING THE WIRING
BY USE OF THE QUICK DISCONNECT. NOTE: ALTHOUGH NOT BY USE OF THE QUICK DISCONNECT. NOTE: ALTHOUGH NOT
NECESSARY, REMOVING SOME OF THE FOUR LENS PANELS NECESSARY, REMOVING SOME OF THE FOUR LENS PANELS
MAY MAKE IT EASIER TO ACCESS AND REMOVE THE POWER MAY MAKE IT EASIER TO ACCESS AND REMOVE THE POWER
PAD. PAD.
4. TO REINSTALL THE POWER PAD REPEAT THE STEPS ABOVE 4. TO REINSTALL THE POWER PAD REPEAT THE STEPS ABOVE
IN REVERSE ORDER. IN REVERSE ORDER.
NOTE: CHECK TO INSURE THAT THE WIRES ARE NOT PINCHED NOTE: CHECK TO INSURE THAT THE WIRES ARE NOT PINCHED
AGAINST THE CASTING DURING RE-INSTALLATION OF THE AGAINST THE CASTING DURING RE-INSTALLATION OF THE
POWER PAD. POWER PAD.
NOTE: BE SURE THAT THE "STREET SIDE" LABEL ON THE POWER NOTE: BE SURE THAT THE "STREET SIDE" LABEL ON THE POWER
PAD IS ORIENTED WITH THE STREET SIDE OF THE UNIT AS PAD IS ORIENTED WITH THE STREET SIDE OF THE UNIT AS
DEPICTED. DEPICTED.
THE SCREWS CAN MOVE FREELY UP AND
TRIGGER LATCH: TO OPEN THE UNIT
PUSHING UP ON THE HOOD WITH YOUR
CLOSING THE HOOD AND PRESSING
PART NUMBER 057-71-67959
HOOD AND RE-