Summary of Contents for Duct-O-Wire RC-P1M1
- Page 1 DUCT-O-WIRE INSTALLATION & OPERATION MANUAL RC-P1M1 RC-P2M1 RC-P3M1 SEPTEMBER, 2018...
- Page 2 FCC ID: NCTSAGA1-L8 IC: 2802A-SAGA1L8 CE 0470 This device complies with part 15 of FCC rules. Opera ons is subject to the following two con- di ons: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interfer- ence that may cause undesired opera on.
-
Page 3: Limited Warranty
God, improper operation, ignorance of environmental specifications, fire, or improper software settings. If your Duct-O-Wire product fails to work as warranted above, Duct-O-Wires maximum liability under this limited warranty is expressly limited to the lesser of the price you have paid for the product. -
Page 4: Operating Precautions
à Always turn off power when installing or providing mainte- nance on unit. à Contents of the Manual may be amended by Duct-O-Wire without notice. à Duct-O-Wire may change functions or new functions may come available and as a result description of units may change. - Page 5 Precautions à After Operating the Pocket series, please press EMS to shut off main power to the Crane & Receiver. à Never continue operating the crane when slow- response occurs. à Only qualified personal should operate this equipment. à The Pocket Series has a rating of IP65. Only use un- der these conditions/rating.
- Page 6 Standard Accessories for the Pocket series. RC-P1M1 RC-P2M1 RC-P3M1 2 Transmi ers 1 Receiver...
- Page 7 8. ID Code Registra on 4. Relay: 5A/250VAC (AC Power) 9. Opera ng range: up to 300 feet 10A/36VDC (DC Power) Pocket Series Transmi er RC-P1M1 1 MOTION 1 SPEED WITH ON/OFF ¨ RC-P2M1 2 MOTION 1 SPEED WITH ON/OFF ¨...
- Page 8 6-1 4 independent COM line U/D, 3. AC type: E/W,S/N RO for RC-P3M1 24/48,48/110,48/220,110/220 6-2 3 independent COM line U/D, 220/380VAC E/W,RO for RC-P2M1 DC Type: 12V-24VDC 6-3 2 independent COM line U/D, 4. Sensi vity: about 105dBm RO for RC-P1M1 5. Shock resistance...
-
Page 9: Emergency Procedures
EMERGENCY PROCEDURES If case of emergency please: Press the STOP bu on ¨ Switch off the main power to the crane ¨ Press Stop Button... -
Page 10: General Operation
General Operation ¨ Turn on the main power switch on the crane. ¨ Install two AA size Alkaline batteries in the transmitter ¨ Press the Star/RO pushbutton to turn on the main relay inside receiver. ¨ Operate normally **After operation** ¨... - Page 11 Receiver Voltage Selection There are two types of power voltage (DC AND AC) Available for the Pocket series. 1 DC TYPE: Input voltage: 12-24VDC Relay contact 10A-36VDC 2 AC TYPE: 5 different transformers: 24/48V,48,110V,48/220V,110,220V,220/380V...
-
Page 12: Changing Fuse
Changing Fuse ¨ DC Type Unplug the yellow 20A fuse and replace ¨ AC Type Depress the fuse cover and turn counter-clockwise with a flat head screwdriver to open up the fuse cover. Re- move old fuse and insert correct fuse into the cover. Place this fuse along with cover into the fuse holder base. - Page 13 ID-Code Remote Setting ID Registration allows you to pair the new TX or RX if one of them is damaged. In order to work the TX & RX must have the same ID codes and frequency. Using ID Registra- tion will make both the TX and RX to have the same ID codes.
-
Page 14: Changing The Frequency
Changing the Frequency It is easy to change the frequency of the pocket series simply by replacing corresponding frequency crystals in both the Transmitter and the Receiver. · Note: To replace a new crystal, please note that there are two kinds of frequencies (VHF and UHF) available. - Page 15 Batteries Two AA size alkaline batteries are required for the Trans- mitter. The LED will flash green when the battery power is suffi- cient. The LED will flash red when the battery power is low. · The operating distance will become shorter and in- termittent when the battery is low.
- Page 16 LED ALERT *If a problem listed below is found please contact us* Red LED flashes quickly (.2 sec) when any pushbutton is pressed. The problem may be: One of the pushbuttons may be jammed. The system is not properly powered. TX LED flashes slowly (.5 sec) The memory of the transmitter is defective.
- Page 17 NOTES:...
- Page 18 NOTES:...
- Page 19 NOTES:...
- Page 20 DUCT-O-WIRE 1351 W. Second Street Oconomowoc, WI 53066 Phone: 262-567-2288 Fax: 262-567-0857 E-MAIL Sales@ductowire.com www.Ductowire.com DUCT-O-WIRE 1445 Norjohn Ct. Unit 10 Burlington, Ontario, Canada L7L 086 Phone: 905-331-2612 800-361-9473 Fax: 905-331-6639 800-663-0933...
Need help?
Do you have a question about the RC-P1M1 and is the answer not in the manual?
Questions and answers