Advertisement

Quick Links

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the POWERMIX 6/3 DIGITAL and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Itec POWERMIX 6/3 DIGITAL

  • Page 2 ITEC POWERDESIGN manual is essential. ITEC POWERDESIGN is a PC Software to configure and control the „ITEC-POWER 6/3 digital“. The technician can easily configure the device as requested and implement a wide variety of sound effects without using additional devices.
  • Page 3: Dear Customer

    Simultaneously, handling is kept very simple and in fact layman-proof. We can ensure you that you have made the right decision in acquiring the „ITEC POWERMIX 6/3 digital“. You now own a product representing state-of-the-art technology and usability with a functional design and a variety of features making daily operation a delight.
  • Page 4: Safety Instructions

    (see also chapter 7). Do not place other devices or objects on the housing of the "ITEC POWERMIX 6/3". Do not try to open the device. No serviceable parts inside. In case of any damage or problems always contact your dealer or the manufacturer.
  • Page 5 POWERMIX 6/3 DIGITAL 2. POWERMIX 6/3 digital: Front panel Fig. 1 POWERMIX Front panel 1. Main switch: Used to turn On/Off the device (additional devices connected to the “AC-OUT” connector are also turned on/off). Devices with an integrated battery pack should be switched on/off by pressing the Master volume button.
  • Page 6 POWERMIX 6/3 DIGITAL 3. POWERMIX 6/3 digital: Rear panel Fig 2 POWERMIX Rear panel 1. Power supply AC-IN Use the supplied power cord to plug into 230 VAC power. Fuse: Glass tube fuse 5x20mm, 5A slow-blow. 2. AC-OUT Switched power supply voltage to connect external devices as for instance Pre- Amplifiers, radio transmitters or any other devices with low power consumption.
  • Page 7 If you need to connect an unbalanced input, use ground and signal+. Connect signal- with ground ! 6. Loudspeaker connector „SPEAKER OUT 2“ (optional) This connector could be used if the optional component „ITEC POWER BOOST 2“ is installed. Pin assignment and features are equal to „SPEAKER OUT 1“ (see item no. 3).
  • Page 8 POWERMIX 6/3 DIGITAL 4. Operation instructions Important notice: „ITEC POWERMIX 6/3 digital“ is a universal device. Features are configured with the PC Software “ITEC_POWERDESIGN” before start-up. Therefore the following figures are examples of a configuration. Each device has its individual configuration and the display views and features of your device can differ from the described ones.
  • Page 9: Main View

    POWERMIX 6/3 DIGITAL 4.1 Main view Independent from your chosen configuration, the display shows a virtual mixer with sliders for each input channel Virtual volume control Battery state (only on devices with integrated battery pack) Name of the active configuration...
  • Page 10: Master Volume Control

    POWERMIX 6/3 DIGITAL 4.3 Master volume control To control the volume for a defined group of inputs (e.g. all microphones), the „Master-Volume“ control could be used. This group depends on your individual device setting. Following inputs of your device are controlled by the „Master-Volume“ Control: ....
  • Page 11 POWERMIX 6/3 DIGITAL 5. Additional Settings and Indicators As mentioned, the „ITEC POWERMIX 6/3 digital“ device can be programmed and configured in many ways using the software “Powerdesign” and a PC. Some important parameters can also be modified directly at the device.
  • Page 12: Connecting To External Devices

    POWERMIX 6/3 DIGITAL 6. Connecting to External Devices 6.1 Playback MC cassette decks, CD players, MP3 players etc, can be connected to the “Line-In” sockets at the connection panel (see also the figure in chapter 6). The volume adjustment is done via the fader labeled “LINE” on the display in mixer mode.
  • Page 13 POWERMIX 6/3 DIGITAL 7. The rechargeable battery (optional) If your device is equipped with a rechargeable battery enabling 6 hours of operation independent from external power sources. Charging the battery The lectern must be turned off while charging. The rechargeable battery will not be charged if the lectern is turned on.
  • Page 14: How To Use

    POWERMIX 6/3 DIGITAL 8. Wireless Microphones (optional accessory) 8.1 How to use Turn on the wireless microphone. Adjust the volume using the fader “WM-1” (WM-2, WM-3) on the display in mixer mode. Check if the microphone works everywhere where it will be used during the lecture or presentation.
  • Page 15: Exchanging Batteries

    8.2 Exchanging Batteries CAUTION: Batteries are hazardous waste. Old batteries have to be disposed of properly. ITEC WM-716 - hand held microphone (also WM 816 and WM 702) Slide battery lid open, remove top battery and then pull the white plastic strip to remove the other two batteries from the battery compartment.
  • Page 16: Specifications

    Diversity receiver UHF or VHF Rechargeable battery (incl. Loading circuit) 12 Volt 7,2 Ah, Operation time ca. 8h Power Amp. „ITEC Power-Boost 2“ 75 Watt, 50/70/100 Volt bzw. 4 Ohm ITEC Tontechnik und Industrieelektronik GesmbH, A-8200 Lassnitzthal 300 / Austria / Europe Tel.: +43 (0)3133 /3780-0, office@itec-audio.com,...

Table of Contents