Subscribe to Our Youtube Channel
Summary of Contents for Cleco LiveWire 943620PT
- Page 1 Instruction Manual P2332BA 2019-08 943620PT, 943610PT WLAN socket tray For additional product information visit our website at www.ClecoTools.com...
- Page 2 Apex Tool Group. Disclaimer Apex Tool Group reserves the right to modify, supplement, or improve this document or the product without prior notice. Trademark Cleco is a registered trademark of Apex Brands, Inc. Apex Tool Group GmbH Industriestraße 1 73463 Westhausen Germany...
-
Page 3: Table Of Contents
Contents About this Document ................5 Safety ....................6 Product description................7 System structure ......................7 Models ......................... 7 Control and function elements..................7 3.3.1 On/Off button ....................... 8 3.3.2 Function keys ......................8 3.3.3 LCD ..........................8 3.3.4 LED display ......................... 8 3.3.5 Status LED ........................ - Page 4 Troubleshooting .................. 19 Technical Specifications ..............21 General Information....................21 Mechanic dimensions and weights................21 Service ....................21 Disposal ....................21 P2332BA | 2019-08 Apex Tool Group...
-
Page 5: About This Document
About this Document The original language of this document is German. Software Version: S169262-100. This document is intended for all persons who will operate and maintain this equipment. This document has the following purposes: • It provides important instructions for safe and effective operation. -
Page 6: Safety
• The pictogram describes the type of danger The product is a part of the Cleco Production Tools tighten- ing system and is intended exclusively for industrial use in Note fastening processes. Use the socket tray under the follow-... -
Page 7: Product Description
1 to 4 1 to 8 Lettering field Number of extension Insert for socket boards LiveWire Memory Chip (LMC) Cleco Production Tools 26V battery Service connection Wireless module, WLAN wireless transmission to control Inductive proximity switch Extension board Mini-USB socket Controller board... -
Page 8: On/Off Button
Information and the menu and submenus are displayed on the LCD (Liquid Crystal Display). See chapter 7 LCD, Seite 15. The MAC address is defined by Cleco Production Tools and cannot be changed. The other data can be changed with LiveWire RF Configuration software via 3.3.4 LED display... -
Page 9: Channel Selector Switch
3.3.9 Channel selector switch Component Each expansion board has one channel selector switch. Battery charger, li-ion 44 V (85 – 270 VAC) Order No. 936491 PT – 1-piece Cable connector (4-pin) Order no. S961042, Order no. Lumberg RKC4/9 Fig. 3-4: Channel selector switch Threaded pin Order no. -
Page 10: Before Initial Operation
Before initial operation 4.1 Components required by the customer Component Phillips screwdriver (PH3) Hexagon key, 2.5 mm 4.2 Adjusting inserts before installation Adjust the inserts for the application concerned. To change inserts, remove the O-rings. Fig. 4-1: Inserts 4.3 Charge battery pack The battery pack is only partly charged upon delivery. -
Page 11: Commissioning
Commissioning 5.2 Configuring the socket tray A detailed description of how to install the S168688 Live- The socket tray initially has no WLAN connection to the Wire Utilities software can be found in the installation nutrunner control. The connection has to be configured via instructions P2372JH. -
Page 12: Starting The Livewsire Rf Settings Program
5.2.3 Starting the LiveWsire RF Settings program When the software package is installed, a folder Apex Tool Group is created. To start the included LiveWire RF Set- tings program: Start the socket tray. Use a USB interface cable to connect the socket tray to the PC. -
Page 13: Updating The Firmware
5.4 Updating the firmware 5.5 Connecting to a nutrunner control system Update the firmware using the LiveWire RF Settings pro- gram. The nutrunner control allows the connection to the socket Select the Tool Identification tab. tray. The corresponding steps are described in the pro- Press <Update Info>... -
Page 14: Operation
Operation 6.3 Initialization error During the initialization phase, the software examines and initializes the connected components. If any faults are 6.1 General Information detected during the initialization phase, the message: Init. failed appears. The controls directly on the socket tray are restricted to: •... -
Page 15: Lcd
7.2 Structure Main menu The operating menu on the socket tray is divided into a main menu and submenus. You can navigate through the Administration menus using the two function keys below the LCD display. Diagnostics Administration In the following description, <F1> is used for the left func- Serial number tion key and <F2>... -
Page 16: Main Menu
7.3 Main menu 7.4 Submenu To change from the main menu to the diagnosis menu, press the On-/Off button or the function key <F2> and hold Diagnostics >Main it for two seconds. To exit the diagnosis menu and return to Diagnostic functions for the socket tray. -
Page 17: Lmc Submenu (Livewire Memory Chip)
7.4.4 Submenu WLAN wireless transmission Initiator test The WLAN wireless transmission submenu shows the set- The functional readiness of the initiators tings being used. Init. can be checked with the initiator test. If no actions are carried out, the menu is automatically test •... - Page 18 Roaming Roamin Sensitivity display Socket tray reaction to change of access point Transmission output TxLeis Transmission output display Channel used Active Display of channel currently used channel Channels scanned ScanCh Display of channels scanned 1,5,9,7,2 UDP/TCP communication protocol Comm Selection of communication socket tray –...
-
Page 19: Troubleshooting
Troubleshooting Problem Possible cause Measure General socket tray Socket tray indicates ini- Expansion board(s) not Check plug connection. tialization error, see inserted correctly. 6.3 Initialization error, Expansion board(s) not Check the setting of the channel selector switch on the Seite 14. - Page 20 Problem Possible cause Measure for WLAN data communication between controller and socket tray No WLAN data communi- The IP address of the On the control screen Tool Setup, check whether the IP cation between the con- socket tray is not cor- address of the socket tray has been entered in the field troller and socket tray.
-
Page 21: Technical Specifications
Technical Specifications 10 Service If repair is required send the complete tool 9.1 General Information to Sales & Service Centers. Repairs are only permitted by Apex Tool Group autho- Ambient Conditions rized personnel. If the tool is opened, the Storage temperature -25°... - Page 22 POWER TOOLS SALES & SERVICE CENTERS Please note that all locations may not service all products. Contact the nearest Cleco® Sales & Service Center for the appropriate facility to handle your service requirements. Sales Center Service Center NORTH AMERICA | SOUTH AMERICA...
Need help?
Do you have a question about the LiveWire 943620PT and is the answer not in the manual?
Questions and answers