Summary of Contents for Eletech LanConn-400
- Page 1 LanConn-400 User Guide User’s Manual First Edition （C）2002-2003 Eletech Enterprise Co., Ltd. All Rights Reserved.
-
Page 2: Specifications
LanConn-400 automatically removes the TCP/IP stack. LanConn-400 also provides a device interface with 4 serial ports and 1 keyboard port, making it a powerful and cost effective solution to many applications such as industrial automation and remote (Internet enabled) device control. - Page 3 4. Hardware Connection Diagram Serial Port 1 Power DC 9V GROUND Serial Port 2 Network GROUND RJ45 DATA Serial Port 3 Keyboard CLOCK GROUND PS/2 Mini-DIN rsRx- Serial Port 4 rsRx+ RS422/RS485 rsTx- rsTx+ GROUND RS422/RS485 LanConn-400 User’s Guide...
- Page 4 Because Etm.exe uses UDP Broadcast Packets, it has the following characteristics: It’s not subject to the subnet restriction – the program is usable even if LanConn-400’s IP and the PC’s IP are not on the same subnet.
-
Page 5: Subnet Mask
IP Address address and click [OK]. Or click [Cancel] to abort the operation Enter the new IP Subnet Mask Enter the Subnet Mask value and click [OK]. Or click [Cancel] to abort the operation LanConn-400 User’s Guide... -
Page 6: Browser Configuration
6. Browser Configuration LanConn-400 supports the HTTP communication protocol. All device configurations can be easily set in the browser program. Just type in the LanConn-400’s IP address, and the following screen will be displayed. The following basic information is shown in the display. - Page 7 • If the correct password is not entered in three tries, you have to wait at least 20 minutes to try again. The following is an example of the configuration screen. LanConn-400 User’s Guide...
-
Page 8: Serial Port
Stop Bit: 1 or 2. • RS232: use only TxD and RxD to transfer and receive data. • RS232 (RTS/CTS): Interface of serial TxD, RxD – transfer and receive data. RTS/CTS – flow control. LanConn-400 User’s Guide... -
Page 9: Serial Port
If the password is not entered within 10 password seconds or a wrong password is entered, then LanConn-400 will automatically disconnect. If a wrong password is entered for three times in a roll, no connection is allowed within 20 minutes. -
Page 10: Serial Port
Baud rate, parity, data and stop bits : 9600, None, 8, 1 Socket port : 103 TCP Server Serial Port 4 Interface : RS 232 Baud rate, parity, data and stop bits : 9600, None, 8, 1 Keyboard Input Socket port 104, TCP Server LanConn-400 User’s Guide... -
Page 11: Ground
After clicking on the [Update] button, the following screen will appear: At this point LanConn-400 is restarting with the new parameters. In about 5 seconds the system will return to the Login screen. LanConn-400 User’s Guide... - Page 12 (1) Make a null modem by connecting pin 2 and 3 together on a 9-pin male RS-232 connector. Plug the null modem on LanConn-400’s RS-232 connector. (2) Connect LanConn-400 onto the LAN, into the same subnet as the testing PC. (3) Execute Hypertrm.exe. The following screen will appear.
- Page 13 You may also send a text file and it will be displayed on the screen. However, you should not use the “Send File” function because the transmission protocols such as Zmodem will cause Hyperterminal to reset LanConn-400. LanConn-400 User’s Guide...
Need help?
Do you have a question about the LanConn-400 and is the answer not in the manual?
Questions and answers