Advertisement
Fill Key Operation:
The ADV 5XXX and the Vending Machine must be READY and ON-LINE.
Press the C button. Watch the Indicator LED's carefully.
The Indicator LED's on the ADV 5XXX will display the following sequence:
DEX audit in progress
"Give your machines a voice
"
TM
DEX completed successfully (15 sec)
Telemetry session in progress
Telemetry Session Completed OK (15 sec)
Unit is Ready and On-Line
By performing a Fill Key operation, you make the ADV 5XXX DEX the
vending machine and make a call, sending the data to the server.
This is the QR code for www.meigroup.com.
MEI
3222 Phoenixville Pike, Suite 200
Malvern, Pa. 19355
Technical Support:
1-800-345-8172
ADV 5XXX Installation Booklet
www.meitechnical.com
18
P/N 250659008_G1
Advertisement
Table of Contents
Summary of Contents for MEI easitrax ADV 5 Series
- Page 1 Fill Key Operation: The ADV 5XXX and the Vending Machine must be READY and ON-LINE. Press the C button. Watch the Indicator LED’s carefully. The Indicator LED’s on the ADV 5XXX will display the following sequence: DEX audit in progress “Give your machines a voice ”...
-
Page 2: Serial Number Configuration
General Information: TABLE OF CONTENTS The MEI | Easitrax Advance 5XXX is a microprocessor based online monitoring device with configurable interfaces to capture General Information Product Description ..………….…….…3 transaction activities of bottling and full-service vending machines ADV 5XXX Installation…...………………….…………..…..…4 through its DEX/UCS communication port. This information can Part Numbers……………………………………………….…...5... - Page 3 The installer should provide additional UV stable cable ties Getting Started to securely fasten all cables to the vendor. Any excess cable should • Contact your MEI sales representative or Authorized MEI Distributor to be fastened to the vending machine and service loops should be discuss system options.
- Page 4 Installation Instructions machine surface. 9) Install wire tie anchors below the ADV 5XXX cable connections. 1) Check vending machine for normal operation and clear all errors. Using the wire ties provided, secure the cable harnesses to the 2) Power the vending machine door. anchors.
- Page 5 ADV 5XXX and the VMC from your Data Shuttle Unit. Figure 4 16) Optional: Use the Survey Tab of the MEI Telemeter Service Tool to inventory the vending machine. Figure 5 The Do’s and Don’ts of a Quality...
- Page 6 Do’ and Don’ts Do’ and Don’ts (continued) AAdvance 5XXX Wiring: Do not coil any cables. Run all The ADV 5XXX should never be cables for every installation. (See Figures 10 and 11) mounted horizontal due to water ingress and visual verification Don’t reasons.
-
Page 7: Operation
Operation: LED Indicators Three red LEDs provide user indications. Each LED can be OFF, ON or Pushbutton Switches: FLASHING. Three push button switches allow user input. The buttons are The LEDs are marked L1, L2, and L3. labeled A, B, and C. The following functions can be performed: LED ON Function LED OFF... - Page 8 Credit Card authorization complete (15 sec) After opening the machine: _____ Confirm that Vending machine firmware is approved by MEI for Credit card failed authorization compatibility with the ADV5XXX. (15 sec) _____ Confirm the Physical ID of the ADV 5XXX (this should match the asset assigned in the vendor system).
-
Page 9: Troubleshooting Checklist
Association for the Advancement of MEI has not approved any changes or modifications to the ADV 5XXX. Medical Instrumentation (AAMI). This standard will allow manufacturers Any changes or modifications could void the user’s authority to...
Need help?
Do you have a question about the easitrax ADV 5 Series and is the answer not in the manual?
Questions and answers