Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for JCM Technologies ACCESS-5K
- Page 1 ACCESS-5K ACCESS CONTROL UNIT...
-
Page 2: Table Of Contents
ACCESS-5K Contents Introduction General description Installation Fixing Wiring Power supply + relays Proximity readers Configuration Verification LED Indicators Maintenance Firmware update Cell battery replacement for time/date loss Technical Data Electrical parameters Physical parameters Radiofrequency parameters Solving problems FAQs Safety instructions... -
Page 3: Introduction
ACCESS-5K Introduction General description The ACCESS-5K is an autonomous access control unit with time scheduling for small installations up to 2 doors. User management is only via Soft Assistant, it is secured against transmitter copies. OPERATION LEDS COMMUNICATIONS CARD CONNECTOR Optionally, if a GSM-CARD COMMS. -
Page 4: Installation
ACCESS-5K Installation Fixing Installation with support UNSCREW REMOVE SUPPORT DRILL SCREW HANG DEVICE Installation without support COMMS. CARD COMMS. CARD 12Vdc LED D0 DRILL UNSCREW OPEN TOP COVER 4 - jcmtechnologies... -
Page 5: Wiring
COMMS. CARD COMMS. CARD ACCESS-5K Installation Wiring Power supply and relays 12Vdc LED D0 12/24V ac/dc 12/24 RELAYS POWER SUPPLY Vac/dc Connect the R1/R2 relay outputs (Normally Connect the power Open Contact) to the existing elements of supply cables the installation... -
Page 6: Proximity Readers
COMMS. CARD COMMS. CARD ACCESS-5K Installation Wiring Proximity readers 12Vdc LED D0 12/24V ac/dc 12Vdc LED D0 PROXIMITY READERS Connect the desired readers to the RD1/RD2 connectors BUS L Channel is defined in EVOPROX configuration WIEGAND26 Channel 1 for RD1 reader Example of installation in EVOPROX readers. -
Page 7: Configuration
ACCESS-5K Configuration This device can be only configured by the software SoftAssitant. Check its user manual and the ACCESS-5K specific annex for details of creating an installation, adding devices, creating user groups etc... MICRO SD CARD SD CARD ADAPTER Insert into the computer... -
Page 8: Verification
ACCESS-5K Verification LED Indicators WARNING (only A5K+) 1 Flash Anti- passback input A activation 2 Flashes Anti- passback input B activation 3 Flashes Radio programming trial 4 Flashes Anti-panic activation COMMS. CARD COMMS. CARD Continous flashing Tamper input activation POWER SUPPLY... -
Page 9: Maintenance
- Delete the firmware file manually in order to allow the device to boot normally. You can also check the current APP version in generated A5KInfo.txt file in SD memory. Replacement of the cell battery In case the ACCESS-5K events lose the date, the button cell battery CR2032 must be changed. 9 - jcmtechnologies... -
Page 10: Technical Data
ACCESS-5K Technical Data Electrical parameters Power Supply 12 / 24V dc/ac Standby / operating consumption <50 mA / 100 mA Maximum power consumption Relay power (R1 / R2) Physical parameters Operating temperature -20ºC … +55ºC Size 180 x 150 x 85 mm... -
Page 11: Solving Problems
A: It is not necessary to block the unit as the codes can only be managed with the SoftAssistant. Q: Can any SoftAssistant read the configuration of my unit? A: ACCESS-5K can be protected through the customer code and the password. Q: How can the events be read? -
Page 12: Safety Instructions
The manufacturer reserves the right to change the specification of the equipment without prior warning. EC Declaration of conformity JCM TECHNOLOGIES, S.A. declares herewith that the product AC- CESS-5K complies with the requirements of the 1999/5/ CEE R&T- TE Directive, and complies with the fundamental requirements of the 2004/108/EC Directive on electromagnetic compatibility and 2006/95/ EC on low voltage, insofar as the product is used correctly.