NAPCO GEM-PXCV Installation Instructions

R
333 Bayview Avenue
Amityville, New York 11701
For Sales and Repairs, (800) 645-9445
For Technical Service, (800) 645-9440
© Napco 2004

GENERAL DESCRIPTION

The GEM-PXCV is a durable hard plastic snap-on cover de-
signed to replace the standard cover of the HID Model 6005B
proximity card reader when used with a GEM-ACM1D Ac-
cess Control System. These instructions detail the mounting
and wiring procedures for the reader, and the installation of
the GEM-PXCV cover.
There are 3 LEDs associated with this combination:
• The HID Model 6005B LED which provides the status of
the access condition (door "locked" or "unlocked"). See
Table 1.
• Two LEDs within the GEM-PXCV which provide the status
of the system condition (system "armed" or "disarmed")
associated with the access Area (see Table 2).
Together, the GEM-PXCV is an indoor/outdoor proximity
card reader providing potted electronics, low power con-
sumption and durability all in a small, easy-to-install package.

LED Indications

The HID Model 6005B reader contains a multicolored LED
Access
Status LED
(see table 1)
System
Status LED's
(see table 2)
Table 1: (Top) Access Status LED (HID Model 6005B)
LED INDICATION
Steady Red
Steady Green
Momentary Green
Alternating Green & Red (Downloading PCD-Windows Program to ACM)
Table 2: (Bottom) System Status LED's (GEM-PXCV)
LED INDICATION
Steady Red
Red LED is off
Blinking Red
Steady Green
Green LED is off
Proximity Reader Cover

Installation Instructions

which provides visual
feedback as to access
condition when access
cards are presented to
the reader.
Table 1 below displays
the LED indications and
their meanings.
The GEM-PXCV module
provides two LED's to
indicate system status,
as displayed in Table 2
below:
ACCESS CONDITION
Door Locked
Door Unlocked
Card Read--Door Remains Locked
SYSTEM CONDITION
System Armed
System Disarmed
System in Alarm
System Ready to Arm
System Not Ready to Arm
GEM-PXCV
Stealth Mode is used to hide the ACM's Armed and Status
LEDs. When Stealth Mode is enabled, the GEM-PXCV sys-
tem status LEDs are normally off but are turned on for 1 min-
ute by any of the following events:
• Press a request to exit button
• Press a request to arm button
• Present a valid ARM/DISARM or ARM card to the reader
When Stealth Mode is disabled ("normal operation"), the
LED's are always enabled and mimic the Keypad Status
LEDs for the following functions only: Armed, Disarmed,
Ready to Arm, Not-Ready to Arm and Alarm. Note: When
the system is in alarm, Stealth Mode is disabled. "Access
Only" cards do not affect the status of Stealth Mode.
Table 3: Proximity Card Reader Connections
GEM-ACM1D Termi- GEM-ACM1D Terminal
nal Number
17 (+)
18 (-)
19
20
21 (-)
22 (-) Red & Green LED
23 (-) Reader Sounder
(Not Used)
(Not Used)
* Tamper Connection not available on HID 6005B
Be sure to place jumper JP1 in correct configuration for 5 volt or 12 volt reader
operation.
Table 4: GEM-PXCV Wire Connections
GEM-PXCV Wires GEM-ACM1D
Terminal
Description
Red Reader Power
Orange Active Low Red
Armed LED
Green Status Green LED

MOUNTING THE GEM-PXCV

Before mounting the card reader, always plan ahead and deter-
mine the route all wires will follow before drilling into wall mount-
ing surfaces. For more information regarding various system
designs, refer to WI1121 for complete installation instructions.
Install the GEM-PXCV as follows:
WI1279 6/04
HID Model 6005B (Prox Point
Description Plus ) Wires
Reader Power Red (+ DC)
Reader Power Black (- Ground) & (Shielded
Ground)
Reader Data 1 White (Data 1)
Reader Data 0 Green (Data 0)
Red LED Brown (Red LED)
Orange (Green LED)
Yellow (Beeper)
(Not Used) Blue (Hold)
(Not Used) Violet (Card Present)
GEM-ACM1D GEM-2D Terminal
Terminal Number
17 (+)
30
31
Number
35 (+)
48
49
1