Summary of Contents for Hydromatic PULTRUDED RAIL SYSTEM
- Page 1 PULTRUDED RAIL SYSTEM NOTE! To the installer: Please make sure you provide this manual to the owner of the pumping equip ment or to the responsible party who maintains the system. Part # 5625-359-1 Item # E-03-359 04/09...
-
Page 2: General Information
(sealing flange should Read and follow these instructions Thank you for purchasing your release easily). for adjusting the pultruded rail Hydromatic pump. To help ® system disconnect. Failure to ensure years of trouble-free Step 2: Attach supplied chain... -
Page 3: Installation Instructions
System Description: Pump Not Operating 2. Discharge Elbow Installation or in Storage: In a Hydromatic Pultruded Rail See Installation Data for the System, the pump is raised and Pumps with carbon ceramic seals proper location of the discharge lowered in the basin using a must have impellers manually elbow on the basin bottom. - Page 4 1 stainless steel cap screws. See Installation Data for typical midpoint of the piping. Secure If Hydromatic door and frame piping arrangement. brace (i.e., U-bolt with angle iron assemblies are not used, obtain strap and angle iron extensions) to 8.
-
Page 5: Pump Maintenance
Pumps alternate protective bushing from inside basin into coupling (all furnished operation on each successive Maintenance cycle with a Hydromatic Control by others). Make connections Panel. The alarm level is usually outside station using wiring, set above the override (both... -
Page 6: Pump Troubleshooting
Disconnect the flexible conduit, sealing flange is reconnected, Pump power and sensor cords from the proceed in a logical manner to Troubleshooting control panel. Pull the pump cord locate and clear the plugging. down through the pipe coupling 6. Discharge head may be too while holding the cord on the The following is a list of common high. - Page 7 right hand to suspend the float, the pump should continue to run. The pump should stop when raising the left hand to suspend the float. If this procedure does not cause the pump to operate as described, either order new 3900 mercury float switches or replace alternator relay.
- Page 8 CONTROL/CABLE MOUNTING BRACKET ELEV. INTERMEDIATE GUIDE RAIL SUPPORT - REQ. FOR DEPTHS EXCEEDING 9'-6" CONTROL/POWER CABLES HYDROMATIC 3900 SUBMERSIBLE LEVEL SWITCHES INFLUENT PIPE INV. EL.: FRP GUIDE RAIL HYDROMATIC NON-CLOG SUBMERSIBLE PUMP HOPPER BOTTOM RECOMMENDED DISCH. ELBOW MIN. WATER LEVEL...
- Page 9 CONTROL/CABLE MOUNTING BRACKET ELEV. INTERMEDIATE GUIDE RAIL SUPPORT - REQ. FOR DEPTHS EXCEEDING 9'-6" CONTROL/POWER CABLES HYDROMATIC 3900 SUBMERSIBLE LEVEL SWITCHES INFLUENT PIPE INV. EL.: FRP GUIDE RAIL HYDROMATIC NON-CLOG SUBMERSIBLE PUMP HOPPER BOTTOM RECOMMENDED DISCH. ELBOW MIN. WATER LEVEL...
-
Page 10: Standard Limited Warranty
12 months ® from the date of shipment from Hydromatic or 18 months from the manufacturing date, whichever occurs first - provided that such products are used compliance with the requirements of the Hydromatic catalog and technical manuals for use in pumping raw sewage, municipal wastewater or similar, abrasive free non-corrosive liquids. -
Page 12: Start-Up Report
Acknowledge that all information is accurate and proper procedures have been followed: Customer Signature:__________________________________________________ Date ___________ Start-up Technician:__________________________________________________ Date __________ Send to: Warranty Department, 740 E. Ninth Street, Ashland, OH 44805, Fax: 419-207-3344, or e-mail to: startupreport@hydromatic.com We will make this a permanent part of our file on this order.
Need help?
Do you have a question about the PULTRUDED RAIL SYSTEM and is the answer not in the manual?
Questions and answers