Pure Reliability SOLO 250 Manual
  1. Manuals
  2. Brands
  3. Pure Reliability Manuals
  4. Flood Light
  5. SOLO 250
  6. Manual

Pure Reliability SOLO 250 Manual

Hide thumbs

Advertisement

Table of Contents

SOLO 250
PR-2255
This product manual contains important information about the safe installation and
use of this projector. Please read and follow these instructions carefully and keep this
manual in a safe place for future reference.
PR LIGHTING LTD.
Yingbin Road, Dashi Panyu, Guangzhou, 511430 China
h t t p : / / w w w . p r- l i g h t i n g . c o m

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SOLO 250 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Pure Reliability SOLO 250

  • Page 1 SOLO 250 PR-2255 This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual in a safe place for future reference. PR LIGHTING LTD. Yingbin Road, Dashi Panyu, Guangzhou, 511430 China...

  • Page 2: Table Of Contents

    Please read and follow these instructions carefully and keep this manual in a safe place for future reference. The SOLO 250 is an innovative projector with an elegant housing, which is made from high intensity and heat–resistant complex plastic. SOLO 250 complies to CE norms and standards and uses international protocol DMX 512.

  • Page 3: Safe Usage Of The Projector

    Always disconnect from the mains, when the device is not in use or before cleaning it or before attempting any maintenance work. If you have any questions, don’ t hesitate to consult your dealer or manufacturer. 3/16 solo 250 manual_last revision_en.doc...

  • Page 4: Installing The Projector

    18Kg for each SOLO 250. For safety the projector should have a secondary fixing with a safety cord through the holes on the underside of the unit.

  • Page 5: Power Supply – Mains

    Note: care should be taken to ensure that none of the connections touch the body of the plug or each other. The body of the plug is not connected in any way. The SOLO 250 accepts digital control signals in standard DMX512 (1990) format.
  • Page 6 5-PIN AND 3-PIN CONVERSION SOLO 250 uses 3-pin XLR plug / socket. If your controller uses 5-pin XLR plug / socket, you should convert 5-pin plug / socket into 3-pin socket / plug as shown below. DMX TERMINATOR In the Controller mode or Master/Slave mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator.

  • Page 7: To Set The Dmx Start Address

    This DMX start address is the channel number from which the projector starts to “ listen” to the digital control information being sent out from the controller. The SOLO 250 has 10 channels, so set the No. 1 projector’ s address 001, No. 2 projector’ s address 011, No. 3 projector’ s address 021, No.

  • Page 8: Dmx Control Channel Functions

    DMX CONTROL CHANNEL FUNCTIONS The SOLO 250 uses 10 DMX channels. They are listed in the following table. CHANNEL DMX VALUE DESCRIPTION 0-33 Open/Clear (5-7: for 5 seconds) Soft reset – See Note 34-66 Gobo 1 67-99 Gobo 2 100-132...

  • Page 9: Stand-Alone Mode & Master/Slave Mode

    When lubricate the bearings, a syringe with a fine needle is the easiest way to introduce the oil to the bearings around each gobo. Do not over lubricate as this will cause spillage when the wheel rotates. 9/16 solo 250 manual_last revision_en.doc...

  • Page 10: Maintenance

    The beam appears dim -Dust or grease contamination Check the optics is clean. on the optics. -The lamp is at the end of its Replace with a new lamp of the life specified type and rating. 10/16 solo 250 manual_last revision_en.doc...

  • Page 11: Technical Data

    Tilt 265º BEAM ANGLE: 12º CONTROL: DMX512: 8 Channels plus 2 for Hi Res. Pan and Tilt Stand-Alone Automatic mode and Master/Slave operation MOTORS: 10 Stepper motors HOUSING: Metal and composite plastic (IP20) WEIGHT: 18Kg 11/16 solo 250 manual_last revision_en.doc...

  • Page 12: Electrical Diagram

    LIGHT OUTPUT ELECTRICAL DIAGRAM 12/16 solo 250 manual_last revision_en.doc...

  • Page 13: Component Order Codes

    290151218 HTD420-3M-140Z TILT DRIVE BELT Note: You may order all parts of the SOLO 250 besides the table listed above. When ordering please state the exact name and part no.. Repairs must be carried out by a qualified technician. 13/16...

  • Page 14: Changing The Operation Voltage And/Or Frequency

    To be carried out by qualified engineers only The power input settings of the SOLO 250 may be changed to suit the supply in the area where the unit is operated. The voltage and frequency is pre-set at the factory and will be marked on the exterior of the unit.
  • Page 15 15/16 solo 250 manual_last revision_en.doc...
  • Page 16 PR LIGHTING LTD. No. 571 Yingbin Road, Dashi, Panyu, Guangzhou, China Post-Code: 511430 TEL: +86-020-84781888 FAX: +86-020-84786023 P/N: 321010085 Last Revision: 06:03:2004 16/16 solo 250 manual_last revision_en.doc...

This manual is also suitable for:

Pr-2255

Table of Contents

Save PDF