Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Axminster Craft AC118CE
Summary of Contents for Axminster Craft AC118CE
- Page 1 Code 105845 Original Instructions AC118CE Cyclone Extractor AT&M: 16/08/2019 BOOK REF : 007840...
- Page 2 Type Cyclone Extractor 2014/30EU EN 61000-3-11:2000 Model AC118CE and conforms to the machinery example for which the EC Type-Examination Certificate No AM 50352808, AE 50398634 has been issued by Laizhou Planet Machinery Co., Ltd. Signed at: Yutai West Street Laizhou, Shandong 261400 China (Mainland) and complies with the relevant essential health and safety requirements.
- Page 4 Preface Before commissioning the machine, please read these operating instructions thoroughly and get familiar with the machine. Please also make sure that all persons operating the machine have read and understood the operating instructions beforehand. Keep these operating instructions in a safety place nearby the machine. Information The operating instructions include indications for safety-relevant and proper installation, operation and maintenance of the machine.
- Page 5 1. Safety This operating instructions ▲explains the meaning and use of the warning notes included in the operating instructions ▲points out the dangers that might arise for you or others if these instructions are not observed. ▲informs you how to avoid dangers. In addition to these operation instructions, please observe ▲the applicable laws and regulations ▲the statutory provisions for accident prevention...
- Page 6 For your own safety, read instruction manual before operating the machine. Learn the machine’s application and limitations as well as the specific hazards peculiar. Always wear approved safety glasses or a face shield when operating or observing machinery to reduce the risk of eye injury or blindness from flying particles everyday. Eyeglasses are not approved safety glasses.
- Page 7 This dust collector is only intended for collecting wood dust and chips from woodworking machines. Do not use this dust collector to collect metal, dirt, pebbles, drywall, asbestos, lead paint, silica, INTENDED USE liquids, aerosols, or any flammable, combustible, or hazardous materials.
-
Page 8: Static Electricity
Plastic dust lines generate high amounts of static electricity as dust chips pass through them. Although rare, sparks caused by static electricity can cause explosions or fire. To reduce this risk, make STATIC ELECTRICITY sure all dust lines are thoroughly grounded by Using a grounding wire. - Page 10 3. Assembly The cyclone dust collector is delivered pre-assembled. After unpacking, the machine must be installed. Transport the dust collector in its packing crate to a place near its final installation site before unpacking it. If the packaging shows signs of possible transport damage, take the necessary precautions not to damage the machine when unpacking.
- Page 12 3.4.2 To assemble machine STEP-1 Install the main frame. Please refer to the following picture. 1.1 Fix the wheels (N) to the base (A) by using the hex socket button screw M6x15 and flat washer Φ6. 1.2 Insert the cover (I) into the four sides of the base (A). ...
- Page 13 1.3 Fix the support (B) on the base (A) by using the hexagon socket button screw M8x16 and flat washer Φ8. 1.4 Fix the transom (C) to the support (B) by using the hexagon socket cap head bolt M8x40, washer Φ8 and hex nut M8.
- Page 14 STEP-2 Install the collection drum. Please refer to the following picture. 2.1 Fix the support connecting bar (K) to the support connecting ring (J) one by one by using the hexagon socket button screw M8x15, flat washer 6, spring washer and hex nut m6. 2.2 Tighten the collector bag (D) to the drum lip (G) by using the bag clamp (Q).
- Page 15 STEP-3 Install the main house assembly. Please refer to the following picture. 3.1 Put the cover (E) to the inlet (F). 3.2 Fix the inlet (F) to the main house assembly (L) by using the Philip head screw M5x8. 3.3 Fix the connector (M) and seal pad (I) to the main house assembly (L) by using the hexagon socket button screw M8x16.
- Page 16 STEP-5 Install the whole machine. 5.1 Install the main housing assembly (A) to the support base (B) by using the hexagon socket button screw M8x16 and flat washer 8. 5.2 Fix the main housing assembly (A) to the support base (B) by using the hexagon socket head cap bolt M8x40 and washer 8.
-
Page 18: Initial Commissioning
3.5 Initial commissioning Once assembly is complete, test run the machine to ensure it is properly connected to power and safety components are functioning correctly. If you find an unusual problem during the test run, immediately stop the machine, disconnect it from power, and fix the problem BEFORE operating the machine again. - Page 23 5.4 Removing/Replacing filter bag Remove and replace the filter bag when it is about 1⁄2 full. To remove & replace filter bag or bags: 1. DISCONNECT MACHINE FROM POWER! 2. Release clamp around bottom of canister filter, then remove filter bag. 3.
-
Page 25: Troubleshooting
7. Troubleshooting Review the troubleshooting procedures in this section if a problem develops with your machine. If you need replacement parts or additional help with a procedure, callb us. Note: Please gather the serial number and manufacture date of your machine before calling. ... - Page 26 Symptom Possible Cause Possible Solution Dust collector does 1. Collection bag full. 1. Empty collection bag. not adequately collect 2. Canister filter clogged/at fault. 2. Clean canister filter; replace canister filter. dust or chips; poor 3. Ducting blocked/restricted. 3. Remove ducting from dust collector inlet and performance.
- Page 27 8. Diagram and part list 8.1 Diagram...
- Page 32 The Axminster guarantee is available on Craft, Trade, Engineer, Air Tools & CNC Technology Series machines Buy with confidence from Axminster! So sure are we of the quality, we cover all parts and labour free of charge for three years! For more information visit axminster.co.uk/3years The packaging is suitable for recycling.
Need help?
Do you have a question about the AC118CE and is the answer not in the manual?
Questions and answers