HOW TO USE ................... 10 SET UP COMPRESSOR................10 PREPARE MOWER ................10 CHECK BLADE FACTORY ANGLE............10 UNFOLD EMBSX .................. 11 SET GRINDER ANGLE ................12 ADD AIR TOOL OIL & CONNECT AIR HOSE .......... 13 CONNECT CAMERA (OPTIONAL) ............14 SHARPEN THE BLADES .................
Add 2 drops of pneumatic tool oil into the quick connect coupling before each use. Call Noracore Inc. if repair is needed. There are no user serviceable parts inside the grinder. See contact info on the back of this manual.
REMOVE ALL PARTS FROM PACKAGE AND IDENTIFY EACH ITEM SHOWN BELOW. MAKE SURE ALL PARTS ARE LOCATED BEFORE DISPOSING OF PACKAGING MATERIALS. IF ANYTHING IS MISSING OR BROKEN PLEASE CONTACT US. A. EMBSX I. Abrasive Bit B. Phone Holder Bracket J. Grinder Wrench - 7/16 in.
ASSEMBLY & SETUP PHONE HOLDER BRACKET & SIDE HANDLE Install the Phone Holder Bracket (B) and Side Handle (E) as shown below using the 3/8in bolt (C) & washer (Part D). Use the provided 7/32” Allen Key (F) to tighten the 3/8in bolt (C). The Side Handle (E) can be mounted either on the left side (Fig.4) or right side (Fig.
ASSEMBLY & SETUP (CONT.) GRINDING BIT INSTALLATION Insert the desired grinding bit into the grinder ATTENTION collet and tighten using the two wrenches provided (J & K) in the direction show below. Protective gloves are recommended when Please make sure it’s tight as the grinding bit handling the Carbide may come loose from vibration during use Bit.
ASSEMBLY & SETUP TOOLS STORAGE The Grinder Wrenches (J & K) and the M4 Allen Key (L) can be conveniently mounted and stored right on the device using the steps shown in Figure 7 and secured with the Thumb Screw (M). CHARGE CAMERA Prior to first use charge the camera controller using the provided wall charger (N) or the USB cable (O) and a portable battery.
HOW TO USE SET UP COMPRESSOR 1. Set the air pressure from your compressor to 120 PSI. If a nozzle attachment is available allow the air to spray out of the hose for 5 – 10 seconds to remove dirt and water. PREPARE MOWER 1.
HOW TO USE (CONT.) UNFOLD EMBSX 1. Flip back the Clamping Handle (4) at the bottom of the handle tube and pull the Quick Release Pin (1) from the handle hinge. Unfold the handle and position it at the desired angle. Retighten the Clamping Handle (4) and reinsert the Quick Release Pin (1).
HOW TO USE (CONT.) SET GRINDER ANGLE 1. Using the M4 Allen Key (L) included with the device adjust the grinding angle by turning the grinding angle adjustment screw. To increase angle turn clockwise and to decrease angle turn counter clockwise. 2.
HOW TO USE (CONT.) PRO TIP Use your smartphone to check the grinding bit angle. On iPhones open the pre-installed app called “Measure” and hit the bottom right tab called “Level”. On Android smartphones download the app called “Bubble Level”. ADD AIR TOOL OIL &...
1. Turn on the camera controller. 2. Download “Dual View” app from the app store. 3. Open the Wi-Fi settings on your smartphone and select “EMBSX” from the list. No password required. 4. Open the camera app and place your smartphone in the Phone holder bracket (B).
HOW TO USE (CONT.) SHARPEN THE BLADES 1. Begin with the blade that is partly exposed next to the discharge chute (if there is one). This will be the easiest since you can see it. Use a bungy cord to tie back the discharge cover to help. Reach under the deck and turn the blade until it is facing the side of the machine.
Page 16
10 sharpening’s to check the balance or if excessive vibration is noticed. DISCLAIMER Noracore Inc. is not responsible for any damage done to the equipment due blade unbalancing. Actual model may vary from images shown...
MAINTENANCE & STORAGE • When storing the sharpener after for longer periods of time add 5 drops of air tool oil into the quick connect coupling on the bottom of the handle and run the grinder for 5 seconds to distribute the oil throughout the unit.
Scope View, Mo-View, HD WIFI, WIFI VIEW, DEPSTECH WIFI. If none of these apps work, please contact us at: support@noracore.com Call Noracore Inc. if repair is needed. There are no user serviceable parts inside. Actual model may vary from images shown...
Contact Us page on our website. You will be required to submit photos of the damage. WARRANTY POLICY EMBSX comes with a limited, one-year product warranty from the date of purchase. Must have proof of purchase. Warranty does not apply to damage due to abuse, negligence, accidents, alterations, normal wear and tear, or lack of maintenance.