Advertisement

Quick Links

O P E R AT O R ' S S A F ET Y
A N D S E R V I C E M A N U A L
" E R G O - TA M P "
This manual covers the following serial numbers
and higher for each model listed:
Ergo-Tamp................7860150
P R O B L E M S O LVI N G
MBW, Inc.
250 Hartford Rd • PO Box 440
Slinger, WI 53086-0440
Phone: (262) 644-5234
Fax: (262) 644-5169
Email: mbw@mbw.com
Website: www.mbw.com
MBW (UK) Ltd.
Units 2&3 CochraneStreet
Bolton BL3 6BN
England, UK
Phone: 44 (0) 01204 387784
Fax: 44 (0) 01204 387797
E-mail: saleseurope@mbw.com
Website: www.mbweurope.com
L20993 / 07.19 G
©MBW, Inc. 2019
Printed in the USA

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ERGO-TAMP and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for MBW ERGO-TAMP

  • Page 1 Ergo-Tamp....7860150 P R O B L E M S O LVI N G MBW, Inc. MBW (UK) Ltd. Units 2&3 CochraneStreet 250 Hartford Rd • PO Box 440 Slinger, WI 53086-0440 Bolton BL3 6BN...
  • Page 2: Table Of Contents

    WARRANTY ......14 Ergo-Tamp Oil ......6...
  • Page 3 WARNING CALIFORNIA PROPOSITION 65 WARNING Engine exhaust and some of its constituents are known in the state of California to cause cancer, birth defects, and other reproductive harm.
  • Page 4: Safety Information

    The publication of these safety DANGEROUS FUELS: Use extreme caution precautions is done for your information. MBW does not by when storing, handling and using fuels, as the publication of these precautions, imply or in any way...
  • Page 5 PT 78 20991 20991 INLINE OILER REQUIRED 21874 21874 DANGER TAMPER JUMPS DURING START- UP. DO NOT PLACE ANY BODY PART ABOVE MACHINE OR BODILY INJURY MAY RESULT. 21302 21302 WARNING Operating, servicing and maintaining this equipment can expose you to chemicals, including engine exhaust, phthalates and lead, which are known to the state of California to cause cancer and birth defects or other reproductive harm.
  • Page 6: Specifications

    S P E C I F I C ATI O N S 786C 786CS Operating Weight 39.3 lbs (17.8kg) 38.1 lbs (17.2 kg) Length 74” (188 cm) 60” (152cm) Foot Diameter 6” (15.2 cm) 6” (15.2 cm) Maximum Pressure 140 psi (965 KPa) 140 psi (965 KPa) Air Consumption 38 cfm (1.1 m...
  • Page 7: Operation

    • Depending on air supply method, adapter(s) may be needed to make connections. • To ensure connections do not leak, MBW recommends using a pipe sealant on the threads of the Ergo-Tamp. Before Starting & Operating • REMEMBER! It is the owner’s responsibility to communicate information on the safe use and proper operation of this unit to the operators.
  • Page 8: Storage

    Storage Release trigger to stop device. • The MBW Ergo-Tamp is made of high quality corrosive • Initiating the Ergo-Tamp might result in a slight delay in resistant components. To lengthen the life of the entire operation, this is normal.
  • Page 9: Maintenance

    Ergo-Tamp Oil page 10. Grease shaft whenever excess hand arm vibration is noticed. To complete maintenance perform the following The MBW Ergo-Tamp requires an inline oil supply to steps. function. Use of the tamper without an inline oiler will Remove bottom zip tie (#17) from top bellow (#11) damage the internal surfaces.
  • Page 10: Service

    Assembly and disassembly should be performed by a 12. Using a 10-32 bolt, pull the spool (#7) out of the valve service technician who has been factory trained on MBW body (#4), then separate the o-ring (#10) and valve equipment. The unit should be clean and free of debris.
  • Page 11: Tamper Assembly

    With body (#10) out of outer shroud (#6), remove Place new o-ring (#16) onto bushing support (#8) and retaining ring (#19) from cap (#13) and then slide seal set (#4) into bushing support (#8) (Note: upper shroud cover off (#7). Position seal set as shown below).
  • Page 12: Replacement Parts

    Their sales engineers are available for professional consultation. If you cannot locate an MBW distributor in your area, contact MBW or one of our Sales Branches listed below. When ordering replacement parts, be sure to have the following information available: •...
  • Page 13: Handle Assembly

    Handle Assembly - 10 -...
  • Page 14 ITEM PART NO. DESCRIPTION 786CS 786C 03810 SEAL, VALVE PIN 03841 FITTING, COUPLER, DIXON 08558 FITTING, ST PARKER8FTX 20905 VALVE BODY 20906 TUBE, OUTER 21298 TUBE, OUTER, SHORT 20907 INNER SHAFT 21299 INNER SHAFT, SHORT 20908 SPOOL 20909 BUSHING, LOWER 20910 HAND GUARD 20912...
  • Page 15: Tamper Assembly

    Tamper Assembly - 12 -...
  • Page 16 ITEM PART NO. DESCRIPTION 08442 CLAMP, WORM DRIVE, SS 20901 ELBOW, 1/8 NPT X 3/8 HOSE 20902 7/8 SHAFT WIPER 20903 SEAL SET, V RING, TEFLON 20904 SHIM, 1.750 X .875 X .048 20913 SHROUD, OUTER 20916 SHROUD COVER, UPPER 20920 BUSHING SUPPORT 20922...
  • Page 17: Warranty

    MBW is not responsible for any liability or damage or assigned to a rental fleet, or otherwise put to first use. injury directly or indirectly from design, material or The obligation under this warranty is limited to the operation of its products.

Table of Contents