Table of Contents
Advertisement
Quick Links
Installation, Service and User
WARNING: THIS APPLIANCE MUST BE EARTHED
ENSURE THAT THE GAS SUPPLY HOSE IS NOT IN
CONTACT WITH OR NEAR THE BURNER BOX
Author: Rudi
Version: 1.0
INSTRUCTIONS
FOR THE
ZERO MODEL:
PR265D
Refrigerator
ZERO APPLIANCES (PTY) LTD
Updated: 2 October 2018
Revision: 1
P a g e
| 1
Advertisement
Table of Contents
Summary of Contents for Zero PR265D
- Page 1 Installation, Service and User INSTRUCTIONS FOR THE ZERO MODEL: PR265D Refrigerator ZERO APPLIANCES (PTY) LTD WARNING: THIS APPLIANCE MUST BE EARTHED ENSURE THAT THE GAS SUPPLY HOSE IS NOT IN CONTACT WITH OR NEAR THE BURNER BOX Author: Rudi Updated: 2 October 2018 Version: 1.0...
- Page 2 Instructions for Installation, Operation & Service Manufacturer: Zero Appliances, Chloorkop, Ext. 44, Kempton Park, Gauteng, South Africa. MODEL: PR265D PARAFFIN Refrigerator & Freezer Important Information and Safety Instructions It is important to read through these instructions carefully before beginning to use the refrigerator.
-
Page 3: Data Plate
Data Plate The data plate, located on the back of the refrigerator will register your model number, serial number and product number. Record these details here, for easier access if the need for a service should arise. Model Number ____________________________ Serial Number ____________________________ Product Number____________________________ Installation Instructions... - Page 4 Insert the one side of the paraffin filler tube (B) into the filler orifice (A). Insert the funnel (C) into the top of the paraffin filler tube (B). See image below. Funnel (C) Paraffin filler tube Paraffin filler tube (B) Filler Orifice (A) Fill the tank with paraffin (kerosene) until the paraffin (kerosene) reaches the maximum filling level on the tank level indicator.
- Page 5 When the paraffin (kerosene) reaches the minimum level on the tank level indicator blow out the flame and repeat steps 3, 4, 5. Lower the soft part of the wick from the bottom of the burner. See image below. Before After Place the burner inside the burner orifice on top of the paraffin (kerosene) tank.
- Page 6 Insert the two pins of the control rod (D) into the two hole of the burner wick adjuster (H). See image below. Wick adjuster (H) To light the burner, remove the flue (F) and gallery (G) together by turning the gallery (G) anti clockwise.
- Page 7 Place the gallery (G) and flue (F) back onto the burner and turn the gallery (G) clockwise until tight. See image below. Be careful not to burn yourself whilst executing this operation. Leave the burner to burn for 5 minutes whilst it is out the appliance. Roll the fuel tank into the correct position.
- Page 8 Adjust the flame with the control rod (D) until it is burning a blue colour without many yellow tips. Please see image below You may have more yellow than blue when using kerosene. Close the fuel tank compartment door. Author: Rudi Updated: 2 October 2018 Version: 1.0 Revision: 1...
- Page 9 REPLACING THE WICK Remove old wick by first removing (a) gallery, (b) flame spreader and (c) outer wick tube and pulling out wick from the top. It may be necessary to grasp the old wick with a pair of needle nosed pliers in order to remove it from the lamp.
- Page 10 6. After the wick raiser is correctly attached to the wick, and it is lined up over the gear inside the knob, gently pull the wick tails down so that the gear engages fully onto the wick raiser teeth. Check this by turning the knob back and forth. If the wick smoothly goes up and down by turning the burner knob, you wick is correctly installed.
-
Page 11: Troubleshooting
20. The appliance should be left running for a minimum of 12 hours before being loaded with products. TROUBLESHOOTING IF THE APPLIANCE FAILS TO WORK: Check the following points before calling for service: 1. That the instructions for starting the appliance have been followed. 2. -
Page 12: Some Useful Hints
6. The ambient temperature is too high. 7. Too many products are loaded into the freezer at one time – air must be able to circulate freely. 8. The lid is not properly closed or the lid seal is defective. 9. -
Page 13: Cleaning Your Refrigerator
The absorption unit must not be opened, since it contains corroding chemicals under high pressure. Who to Contact For service of your Zero refrigerator, please firstly contact your selling agent. Author: Rudi Updated: 2 October 2018 Version: 1.0...