Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for LOGICDATA DMD660
- Page 1 MANUAL Document Version 1.0 / October 2018 DMD660...
- Page 2 DMD660 - OPERATING MANUAL // PAGE 2 DMD660 - Operating Manual Document Version 1.0 / October 2018 This document was originally published in English. LOGICDATA Electronic & Software Entwicklungs GmbH Wirtschaftspark 18 8530 Deutschlandsberg Austria Phone: +43 (0) 3462 51 98 0...
-
Page 3: Table Of Contents
DMD660 - OPERATING MANUAL // PAGE 3 CONTENTS General information Other applicable documents Copyright Royalty-free use of images and text Trademarks Safety Target audience General safety regulations and obligations Intended use Reasonably foreseeable misuse Explanation of symbols and signal words... - Page 4 DMD660 - OPERATING MANUAL // PAGE 4 Inserting the Actuator 7.2.1 Required Components 7.2.2 Process Completing Assembly Assembly - Thick Tube Down Required Components 8.1.1 Middle Tube Adapter Process Completing Assembly Assembly - End Points Step 1 - Attaching the Motor End 9.1.1 Required Components...
-
Page 5: General Information
Height-Adjustable Table Systems. The license does not include logos, designs, and page layout elements belonging to LOGICDATA. The Reseller may make any necessary changes to the text and images to adapt them for the purpose of end user documentation. Texts and images may not be sold in their current state, and may not be published or sublicensed digitally. -
Page 6: Safety
2.3 INTENDED USE The DMD660 is a Spindle Actuator for electrically Height-Adjustable Tables. It is installed by Resellers in a Height-Adjustable Column for electrically Height-Adjustable Tables. It is controlled by an integrated Control Unit. -
Page 7: Explanation Of Symbols And Signal Words
2.6 LIABILITY LOGICDATA products comply with all currently applicable health and safety regulations. However, risk can result from incorrect operation or misuse. LOGICDATA is not liable for damage or injury caused by: • Improper product use • Disregard of the documentation •... -
Page 8: Residual Risks
Residual risks associated with assembly and instal- lation of the DMD660 are listed here and throughout this Operating Manual. The risks associated with the system as a whole are listed in the System Manual. See also Chapter 1.1 Other Applicable Documents on page 5. -
Page 9: Skilled Persons
Ensure that persons with limited ability to react to danger do not take part in the assembly process The DMD660 may only be assembled by Skilled Persons. A Skilled Person is defined as someone who: • Is authorized for installation planning, installation, commissioning, or servicing of the product •... -
Page 10: Scope Of Delivery
DMD660 - OPERATING MANUAL // PAGE 10 3 SCOPE OF DELIVERY The standard scope of delivery for the DMD660 consists of the following components: DMD660 Linear Actuator The Top Plate Mounting Screws must be ordered from LOGICDATA separately. All other components required for assembly, e.g. the Adapter Sleeve and Fixing Ring, the Middle Tube Adapter, the Top Plate and Bottom Plate, and the Bottom Plate Mounting Screw are to be provided by the Reseller unless otherwise stated by LOGICDATA. -
Page 11: Product
Thick Tube Down) Spindle End Attachment Point ACTUATOR DIMENSIONS Fig. 1 shows the dimensions of the DMD660 in its reset position, installation position, and extended posi- tion. Retracted Length (reset position): 509.20 mm (+2 mm / - 2 mm) Installation Length (as-develivered condition): 511.70 mm (+2 mm / - 2 mm) Extended Length (full stroke): 1173.20 mm (+3 mm / - 3 mm) -
Page 12: Pre-Assembly
Power Hub, etc.) for that product’s mounting instructions, and the System Manual for instructions on con- necting the system. The processes shown in Chapters 7, 8, and 9 assume the DMD660 is to be installed in a Height-Adjustable Column in which the Top Plate can be removed (i.e. it is not permanently connected to the Tube closest to the Table Top). -
Page 13: Assembly Variants
DMD660 - OPERATING MANUAL // PAGE 13 6.2 ASSEMBLY VARIANTS There are two assembly variants for the DMD660. The variant you require depends on the type of Height- Adjustable Column that the Actuator will be installed in. These are defined as follows: •... -
Page 14: Synchronous Movement
DMD660 - OPERATING MANUAL // PAGE 14 6.2.1 SYNCHRONOUS MOVEMENT The DMD660 must be attached to the Middle Tube of the Height-Adjustable Column. This allows the Middle Tube of the Height-Adjustable Column to move synchronously. The distance between the Middle Tube and the Motor End is always the same as the distance between the Middle Tube and the Spindle End (Fig. -
Page 15: Preparing The Actuator
Before starting assembly, you must prepare the Motor End and Spindle End of the DMD660 Actuator. 6.3.1 ADJUSTING THE MOTOR END Before it can be mounted into the Height-Adjustable Column, the Motor End of the DMD660 must be in the correct position. Proceed as follows to achieve this position: 1. -
Page 16: Assembly - Thick Tube Up
This section describes assembly for the DMD660 into "Thick Tube Up" Height-Adjustable Columns. The "Thick Tube Up" variant requires the installation of an Adapter Sleeve (7.1.1 Required Components). If you are installing the DMD660 into a “Thick Tube Down” Height-Adjustable Column, skip this chapter and continue at Chapter 8. -
Page 17: Process
To attach the Adapter Sleeve: 1. Properly lubricate the Actuator's Spindle Nut to minimize friction between the Adapter Sleeve and the DMD660. Consult LOGICDATA for a list of recommended lubricants. Lubricate here 2. Slide the Adapter Sleeve along the Actuator so that it snaps into place at the Motor End. -
Page 18: Inserting The Actuator
DMD660 - OPERATING MANUAL // PAGE 18 7.2 INSERTING THE ACTUATOR At this stage of assembly, the DMD660 is attached to the Middle Tube of the Height-Adjustable Column using a special Middle Tube Adapter. This component is supplied by the Reseller. -
Page 19: Assembly - Thick Tube Down
Middle Tube Adapter (mounted into the Height-Adjustable Column) 8.1.1 MIDDLE TUBE ADAPTER The Middle Tube Adapter (Fig. 8) fixes the DMD660 to the Middle Tube of the Height-Adjustable Column. It is supplied by the Reseller. Fig. 8: Example of a Middle Tube Adapter (Thick Tube Down) The Middle Tube Adapter must be securely fixed into the Middle Tube of the Height-Adjustable Column before the assembly process can begin. -
Page 20: Process
INFO Contact LOGICDATA for advice on suitable production aids, joining forces and joining speeds. Failure to perform the process properly may result in damage to the DMD660. 1. Mount the Middle Tube Adapter into the Middle Tube 2. Insert the three Tubes of the Height-Adjustable Column into each other 3. -
Page 21: Assembly - End Points
To attach the Motor End of the DMD660: 1. Insert the Mounting Screws through the Top Plate into the holes at the top of the DMD660 2. Use the Torque Screwdriver to tighten the Screws to 2.5 - 3 Nm. -
Page 22: Step 2 - Attaching The Spindle End
Use a Torque Screwdriver to tighten the Screw 9.2.3 COMPLETING ASSEMBLY After the DMD660 is attached to the Height-Adjustable Column, you must connect the Actuator Cable to the System. Refer to the DYNAMIC MOTION System Manual for instructions on your chosen configuration. -
Page 23: Additional Information
A full list of Software-Dependent Functions can be found in the DYNAMIC MOTION System Manual. 10.3 DISASSEMBLY To disassemble the DMD660, ensure that it has been disconnected from the Power Unit. Then, follow the assembly instructions in reverse order. 10.4 MAINTENANCE The DMD660 is maintenance-free for its entire service lifetime. - Page 24 LOGICDATA LOGICDATA North America, Inc. Electronic & Software Entwicklungs GmbH 1525 Gezon Parkway SW, Suite C Wirtschaftspark 18 Grand Rapids, MI 49509 8530 Deutschlandsberg Austria Phone: +43 (0)3462 5198 0 Phone: +1 (616) 328 8841 Fax: +43 (0)3462 5198 1030 Email: office.na@logicdata.net...