Page 2
Die Abluft muss mit dem optionalen Abluftschlauch (A) direkt aus einem Unterschranksystem heraus geführt werden, wenn bestehende Abluftöffnungen nicht den folgenden Abbildungen (B, C) entsprechen. The exhaust air must be allowed to escape directly from the cupboard by means of the optional- ly available exhaust air duct (A) if the existing opening vents do not correspond to the following pictures (B, C).
Contents Introduction ����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 1�1 Symbols ����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� Safety ������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 2�1 Intended Use ������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������ 2�2 Improper Use ����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 2�3 Ambient Conditions for Safe Operation ����������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 2�4 Ambient Conditions for Storage and Transport ��������������������������������������������������������������������������������������������������������������������������������������������������������� 2�5 Hazard and Warning Information ��������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 2�5�1 General Information ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������...
The manufacturer shall not be liable for damages caused by improper use� Only spare parts and accessories supplied or authorized by Renfert GmbH may be used with this prod- uct� If other spare parts or accessories are used, this could have a detrimental effect on the safety of the device, increase the risk of serious injury and lead to damage to the environment or the device itself�...
Ambient Conditions for Safe Operation The device may only be operated: • Indoors • Up to an altitude of 2,000 m above sea level, • At an ambient temperature of between 5 - 40 ºC [41 - 104 ºF] *), •...
► The product is altered in any way other than those alterations described in the operating instruc- tions. ► The product is not repaired by an authorized facility or if non-original Renfert parts are implemented. ► The product continues to be used despite obvious safety faults or damage.
Product Description General Description This is a workplace and appliance suction unit for extracting dust in dental laboratories� The extraction unit comprises two suction channels, one suction point can be connect-ed to each chan- nel� The extraction unit can be operated both manually and automatically, depending on the connected, elec- trical, dust-generating equipment�...
Glass screen with holder (for the extractor clamp) 2926 0000 Suction switch, incl� 4 bushings (without hose) 2937 0002 External exhaust air 2934 0007 90° angled connector Silent For more details or further accessories, please see www.renfert.com - 7 -...
Initial Operation Unpacking ⇒ Remove the device and accessories from the package� ⇒ Check the delivery for completeness (compare the list included in delivery)� Setting-up The suction unit is a standing device which must not be operated in a horizontal position� Place the suction unit so that: •...
⇒ Place the suction tube onto the suction port (6A / 6B)� Observe the allocation of the device sockets (A, B) – suction channel (A, B)� ⇒ Connect the suction tube to the correct suction point� If the diameter is not suitable, use an adapter (see accessories), to avoid loss of suction. Avoid steep sloping and “sagging”...
Operation After switching on, the suction unit is in standby mode� If a suction channel is activated, the suction turbine switches on with the last set suction power level and the associated pinch valve is opened� MENU If the second suction channel is then activated, the second pinch valve opens� The opening / closing of the suction channels takes place: •...
5.3.1 Automatic Filter Cleaning ♦ Suction turbine is stopped� ♦ The symbol “dust drawer” blinks� ♦ “CLEAn” is shown in the display� ♦ An acoustic signal indicates the cleaning is about to commence� ♦ The cleaning is carried out� ♦ Suction turbine starts again� 5.3.2 Manual Filter Cleaning ⇒...
Page 17
5.4.2 Time Interval for “Full” Display Dust Drawer After reaching a set time interval, a request appears to empty the dust drawer� You can select between 5 times (factory setting 50 hrs)� Time interval / hrs Value in display (24, Fig. 2) MENU To change: ⇒...
In order to prevent the suction from being switched on / off too often, or the suction performance to be adjusted too frequently in the case of short interruptions (for example when working with the handpiece), a higher time value should be selected. MENU MENU To change:...
If the dust drawer is not emptied, the “Dust drawer full” and “FULL” symbols are still shown in the display. After switching the device off and on again, a 3 x acoustic signal is used to indicate the emptying of the dust drawer. Change Fine Filter The effectiveness of the filter cleaning is determined by monitoring the flow rate (internal pressure sen- sor)�...
Send the device in for repair! Spare Parts You can find components subject to wear and the spare parts on the spare part list in the internet at www.renfert.com/p918� Enter the following item number: 29370000� The components excluded from the warranty (such as consumables or parts subject to wear and tear) are marked on the spare part list�...
• Turbine does not run even though elec- • Check whether the turbine cable is properly tronics have been switched on� plugged in (especially after changing the turbine)� • Faults in electronics� • Contact Renfert / Service� “FILt” is shown in the • The fine filter is so heavily clogged that • Change the fine filter (see accessories as well as display.
Page 22
Trouble Reason Solution The suction performance • Suction performance is set too low� • Select a higher suction level� is insufficient. • Blockage in the Suction tube� • Check suction tube� • High loss of suction due to unfavorable • Read instructions on connection to the extraction tube position�...
**) Sound pressure levels according to EN ISO 11202 Warranty Provided the unit is properly used, Renfert warrants all components for 3 years. SILENT EC2: The suction motor is guaranteed for 3 years, or a maximum of 5000 operating hours (engine running time).
10 Disposal Information 10.1 Disposing of Consumables Full dust bags and filters must be disposed of under compliance with locally applicable regulations. Depending on the material trapped by the filters, protective gear may need to be worn during disposal. 10.2 Disposing of the Unit The unit must be disposed of by an authorized recycling operation. The selected firm must be informed of all possible health hazardous residues in the unit� 10.2.1 Disposal Instructions for countries in the EU To conserve and protect the environment, prevent environmental pollution and improve the recycling of raw materials, the European Commission adopted a directive that requires the manufacturer to accept the return of electrical and electronic units for proper disposal or recycling�...
Page 25
Montageanleitung • Assembly Instruction • Instruction d’installation Istruzioni l’istallazione • Instrucciones de montaje • Руководство по монтажу 90002 1584 Feinfilter SILENT TC / EC • Fine filter SILENT TC / EC • Filtre fin SILENT TC / EC Filtro fine SILENT TC / EC • Filtro fine SILENT TC / EC • Фильтр тонкой очистки SILENT TC / EC 2 seconds - 1 / 4 -...
Need help?
Do you have a question about the SILENT C2 and is the answer not in the manual?
Questions and answers