Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Gulf Coast Spas Manuals
  4. Fan
  5. Coastal Air 5GR
  6. Owner's manual

Gulf Coast Spas Coastal Air 5GR Owner's Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
Coastal Air
(5GR)
Net weight
5.8 KGS.
12.8 LBS.
WARNING : Read and follow these instructions carefully and be mindful of all warnings shown throughout.

Advertisement

loading
Need help?

Need help?

Do you have a question about the Coastal Air 5GR and is the answer not in the manual?

Questions and answers

Summary of Contents for Gulf Coast Spas Coastal Air 5GR

  • Page 1 Coastal Air (5GR) Net weight 5.8 KGS. 12.8 LBS. WARNING : Read and follow these instructions carefully and be mindful of all warnings shown throughout.
  • Page 2 READ AND SAVE THESE INSTRUCTIONS WARNING : TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS, PLEASE OBSERVE THE FOLLOWING : 1]. To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly before beginning.
  • Page 3 Unpack and inspect fan carefully to be certain all contents are included. Hardware Bag Mounting Bracket For Wire Connection: Wire Nut x 8 For Blade Installation: Rubber Washer x 11 (one spare washer included) Canopy Blade Screw x 11 (one spare screw included) Motor Screw x 16 (one spare screw included) Wire...

  • Page 4: Blade Installation

    WARNING: BLADES SHOULD BE AT LEAST 7 FEET FROM FLOOR Note 1: Note 2: Turn off power at breaker Use metal outlet box suitable box to avoid possible for fan support. electrical shock. Outlet box must support 35 lbs min. OF F OF F OF 1.
  • Page 5 3. DOWNROD INSTALLATION Yoke Cover Plastic Fastener Yoke 3-1. Erect the lying downrod assembly up to 3-2. Push the plastic fastener into slots of yoke. vertical position. Canopy 3-3. Yoke Cover Downrod Assembly 3-4. Insert the canopy onto downrod assembly. 3-3.
  • Page 6 4. HANGING THE FAN ONTO MOUNTING BRACKET Mounting Bracket Mounting Bracket Ridge Ball Groove 4-1. Lift fan assembly onto mounting bracket. 4-2. Rotate fan so that the groove on the ball engages the ridge in the mounting bracket. 5. ATTACH THE SWITCH HOUSING BACK Mounting Bracket Canopy Switch Cover Screws(3)

  • Page 7: Wire Connection

    6. WIRE CONNECTION 6-1. Verify that serial Number & Model Number match on the Receiver and Transmitter NOTICE: Many remote sets for DC fans look the same. This remote set is pre-paired and labeled at the factory, please note the following before operation: 1a.

  • Page 8: Canopy Installation

    7. CANOPY INSTALLATION 7-3.Screw (4) 7- 2.L Type Slots (Tightening) 7-1.Left-hand side screw (Removing) Screw (Loosening) Note: Four screws are pre-screwed on mounting bracket for canopy installation. 7- 2. Push up the canopy and rotate the canopy slightly 7-1. Remove left-hand side screw on mounting until both two loosening screws are in the holes of L bracket first and loosen the other one.

  • Page 9: Operational Instruction

    9. OPERATIONAL INSTRUCTION All the button pressed will have a Beep sound and the red indicator light will turn on. 9-1. ON/OFF - Fan 9-1. Press button to turn the fan ON/OFF. 9-5. Indicator Warning: DO NOT PRESS THE BUTTON FOR MORE THAN 4 SECONDS TO AVOID 9- 7.
  • Page 10 10.REMOTE PAIRING PROCESS The Pairing Process is only necessary when there is an issue. Remote set is pre-paired from the factory and should not require the Pairing Process. A fan may need to have “Pairing Process” performed for the following issues. 1.
  • Page 11 10-4. TO SET UP REMOTE FOR #2 FAN Make sure to turn off power at breaker box. Disconnecting wire from #1 Fan Disconnect the Black wires from #1 Fans and connect the Black wires back to #2 Fan that you remove from 10-3. Outlet Box Outlet Box (Disconnecting)