Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for Heat Storm 55 inch Storm Shell
- Page 1 STORM SHELL Assembly and Installation Instructions for 55" Storm Shell TV Hard Cover and Wall Mount...
- Page 2 Caution • Prior to installation of this product, the installation instructions should be read and completely understood. The installation instructions must be read to prevent personal injury and property damage. Keep these installation instructions in an easily accessible location for future reference.
-
Page 3: Tools Required
Tools Required • Electronic stud finder for drywall installation • Phillips head screw driver or electric drill • Bubble Level • Crescent wrench • 13 mm socket and wrench • Electric drill, 1 8 ⁄ " and 1 4 ⁄ ” drill bit for wood stud installation. Centering the Storm Shell Hard Cover –... - Page 4 Storm Shell and TV Mounting Bracket Parts 1. Storm Shell Front (left part) 1 pc 2. Storm Shell Front (right part) 1 pc 3. Storm Shell Back (left part) 1 pc 4. Storm Shell Back (right part) 1 pc TV bracket (preassembled in Storm Shell Back right part) 1 set...
- Page 5 Connecting Parts 1. Top Connecting Bar 1pc 2. Bottom Connecting Bar 1 pc 3. Angle Brackets 2 pcs 4. Middle Connecting Plate 1 pc 5. Buckle Latch 4 sets Screws Name Picture Name Picture M8X15 Screw ST8.0X60 Lag Bolt M4X8 Screw 3-hole Washer...
- Page 6 Assemble the Storm Shell Back 1. Remove the TV Bracket from the Storm Shell Back right part by removing the four securing bolts. Figure 2. Figure 2 2. Place the Storm Shell Back right part and left part together. Connect the two parts using four (4) S3 bolts with four (4) N2 flange nuts as shown in Figure 3.
- Page 7 3. Attach the two (2) Angle Brackets using four (4) S3 bolts for each bracket and four (4) N2 Flange Nuts as shown in Figure 4. Note: The bolt head is placed on the outside of the Storm Shell Back and the flange nuts are secured on the inside.
- Page 8 Assemble the Storm Shell Front 5. Place the Storm Shell Front left part and right part together. Connect the two parts together using the Top Connecting Bar with two (2) S2 bolts. The S2 bolts are placed through the Storm Shell Front top plastic and secured into the threaded holes in the Top Connecting Bar.
- Page 9 Bolts: S2- M4X8 screw: 2 pcs Figure 7 Nuts: N2-M4 flange nut: 12pcs Figure 8...
- Page 10 Install the Storm Shell Back onto the wall Two people are needed for this installation. A) Wood Stud Installation 1. Use a high quality electronic stud finder (commercially available) to locate dead center of four adjacent wood studs spaced 16” apart. Mark the location of each stud (Figure 9). If a different placement of the 55”...
- Page 11 3. Lift the Storm Shell Back to the wall and position the S8 screw head (Step 2) into the top right keyhole (Figure 10). Place a bubble level on top of the Storm Shell Back and rotate until the Storm Shell Back is Level. Place a mark on the wall through the top left keyhole. Make sure to mark the top left key hole at the center of the top (where the screw will rest).
- Page 12 5. Hang the Storm Shell Back on the wall. Use a 13 mm socket and wrench to attach the TV Bracket using the S9 Lag Bolts and the W3 washers (note the washers are placed between the S9 bolt head and the TV Bracket mounting hole). Ensure that the TV Bracket is level and installed in the right direction.
- Page 13 Install the Storm Shell Front and check that cover and latches fit correctly. Figure 14. Figure 14 B) Concrete or Brick Installation When installing the Storm Shell Hard Cover and TV Bracket on a concrete or brick wall, the S8 and S9 screws alone will not be sufficient.
- Page 14 Install the TV Display Caution: This TV bracket can be used for a TV up to 55". The maximum weight of the TV display should be less than 66 lbs. (30 kg.). The installation kit includes screws of various diameters to ensure optimal installation. Figure 15 shows the parts of the TV Bracket.
- Page 15 Figure 16 6. Assemble the two Vertical Bars onto the Horizontal Bars using four (4) S1 bolts, with W3 washers and N1 nuts as shown in Figure 17. The Vertical Bars slide into the Horizontal Bars (see Figure 18 for correct assembly). The Vertical Bars must be spaced to match the width ⁄...
- Page 16 8. Lift the TV Display (with the Hook Plate firmly attached to the back) and slide the Hook Plate in place on the Swing Arm (Figure 19). Replace the securing screws that were removed in Step 5. Figure 19 Set TV Cables Figure 20...
Need help?
Do you have a question about the 55 inch Storm Shell and is the answer not in the manual?
Questions and answers