Subscribe to Our Youtube Channel
Summary of Contents for SHERMAN-profi MIG 251Y
- Page 1 V1.9 16/03/24 USER MANUAL SEMI-AUTOMATIC WELDING inverters MIG 251Y, 280Y MIG, MIG 320Y Sherman...
- Page 2 EDGE WITH EQUIPMENT! EDGE WITH EQUIPMENT! EDGE WITH EQUIPMENT! before installation and and start-up device and equipment should with y acquainted Æ si ę with this and instructions and before installation and and start-up device and equipment should with y acquainted Æ si ę with this and instructions and before installation and and start-up device and equipment should with y acquainted Æ...
- Page 3 • use Æ protective veil of non-combustible materials and WŁA ś properly chosen Æ color patterns E S absorbing walls and smokers harmful use Æ protective veil of non-combustible materials and WŁA ś properly chosen Æ color patterns E S absorbing walls and smokers harmful use Æ...
-
Page 4: Specifications
251Y MIG, MIG 280Y and 320Y MIG s and identical device and different devices with than and si ę only parameters. 4. SPECIFICATIONS 4.1 welder MIG 251Y MIG 280Y MIG 320Y Napi ę a supply: Napi ę a supply: Napi ę... - Page 5 General view of the device and equipment General view of the device and equipment General view of the device and equipment 5. CONSTRUCTION AND OPERATION Fundamentals and the construction of the power conversion welder s and electronics made in IGBT technology enables with Livia and ce work ę in terms of Fundamentals and the construction of the power conversion welder s and electronics made in IGBT technology enables with Livia and ce work ę...
- Page 6 1. office and device should be Æ at with off final useful and only in three-phase power supply system, a four-earthed neutral. 2. Semi-automatic MIG 251Y is compatible with the network and 3x400V 50 Hz 2. Semi-automatic MIG 251Y is compatible with the network and 3x400V 50 Hz 2.
- Page 7 6.4 PREPARATION FOR WORK MIG depending on with Well ś the type of material being welded and ś diameter wire electrode assumptions with s Æ for MIG respectively numbered and ko ñ tip depending on with Well ś the type of material being welded and ś diameter wire electrode assumptions with s Æ for MIG respectively numbered and ko ñ tip depending on with Well ś...
-
Page 8: Protection Against Overheating
Adjusting the inductance ś you (reluctance arc) Adjusting the inductance ś you (reluctance arc) Adjusting the inductance ś you (reluctance arc) Adjusting the inductance ś allows you with you to optimize ę depending on the characteristics of the arc with Well ś those of coarsely ś of the work piece and Adjusting the inductance ś... - Page 9 11. Before calling service, In the event of a malfunction device and equipment, welding before sending to the site should with s check Æ letter ę basic failure and try Æ remove them In the event of a malfunction device and equipment, welding before sending to the site should with s check Æ letter ę basic failure and try Æ remove them In the event of a malfunction device and equipment, welding before sending to the site should with s check Æ...
-
Page 10: Maintenance Instructions
List rts You consumables welding methods and MIG / MAG: part List rts You consumables welding methods and MIG / MAG: part List rts You consumables welding methods and MIG / MAG: MIG 251Y For steel wire For aluminum wires... -
Page 11: Electric Scheme
16. ELECTRIC SCHEME 16.1 MIG251Y... - Page 12 16.2 MIG280Y...
- Page 13 16.3 MIG320Y...
- Page 14 17. Warranty Warranty is granted a ę for a period of 12 months ę months leading actors and smokers activity SC economic and 17. Warranty Warranty is granted a ę for a period of 12 months ę months leading actors and smokers activity SC economic and 17.
-
Page 15: Rohs Directive 2011/65 / Eu
We declare, with e ni with the articles mentioned above: We declare, with e ni with the articles mentioned above: Type inverter welder MIG 251Y, 280Y MIG, MIG 3 20Y Manufacturer's trademark: which refers ę this assurance and requirements ff ę following and smokers of European Union directives and national rules enter and These smokers which refers ę...
Need help?
Do you have a question about the MIG 251Y and is the answer not in the manual?
Questions and answers