Susan McKnight Climbup Directions For Use

1.

Installation:

 When handling the devices only touch the outer wall of the device.
The inner walls are pre-lubricated with talc which can be easily
rubbed off when handled.
 Place Climbup
®
devices under each leg of the furniture where people
sleep or rest (beds, sofas, armchairs etc.) so that the leg rests within
the center well of the device (See fig #1). In order to avoid injury, be
sure to use proper lifting techniques and do not lift any objects that
too heavy for you to lift properly.
 Eliminate all other pathways for bugs to access furniture. "Bridges"
for bed bugs to travel on will be created if the furniture is touching a
wall or another object, or anything is hanging off of the furniture onto
the floor. For example, all sheets and comforters should always be
tucked in, and no items should be allowed hang down and touch the
floor. All electric cords should be disconnected between bed and wall.
Any items on the furniture that are touching the floor or wall will
provide bed bugs a "bridge" to access the furniture bypass the
Climbup® devices. It is important that the only avenue onto the
furniture is via the legs that are contained within the Climbup® insect
interceptor.
 The monitors should be left in place for a minimum of 21 days to
provide the best opportunity to intercept bed bugs as they move
around your home. Ideally, the monitors should be left in place
indefinitely so that they are continually monitoring for bed bugs.
2.

Once installed:

 Continue to keep furniture pulled away from the wall and do not
allow any objects on furniture to contact the floor or wall.
 Periodically observe the Climbup® devices for bed bugs. Bed bugs
approaching bed from room will be in the outer pitfall ring. Bed bugs
climbing down from bed will be found in center well. Remove bed
bugs from device by wiping out with cotton ball with a small quantity
of talc and immediately place cotton ball in sealed plastic bag for
disposal.
 Check the Climbup® devices to make sure that they have not become
compromised in any way.
Examples include but are not limited to:
a. Checking for the presence of debris or other items present in the
wells that may provide a method for the bugs to escape the wells.
b. Checking to see if the talcum powder has rubbed off or has been
covered in dust.
c. Checking to see if furniture legs have broken the plastic floor of
the inner well
** NOTE: If the any of the Climbup® devices are compromised
in way, debris will need to be removed, the device
relubricated, or discarded. It is important to
exercise care when checking or handling Climbup®
devices after they have been installed as live bugs
may be in, on, or around the devices.
3. Handling Climbup®Insect Interceptors After Installation:
It may become necessary to handle Climbup® devices from time to time
to remove debris and/or bugs or to discard the devices. Care should be
taken when handling Climbup® insect interceptors after installation as
live bugs may be in, on, or around the devices. When handling devices
be sure to:
 Remove device carefully from beneath the legs of the furniture
 Wash device in soapy water to fully immerse all of the bugs
 Empty soapy water containing bugs into the toilet. The trap may need
to be rinsed more than once to remove all of the bugs. After
emptying soapy water and bugs into the toilet the toilet should be
flushed. Physical debris should not be flushed down toilets but can
be placed into a sealed bag for disposal in an outdoor trash receptacle.
 Fully dry the outer wall as well as the inner walls and wells of the
Climbup® with a paper towel. The paper towels should be
immediately sealed in a plastic bag and discarded in an outdoor trash
receptacle.
®
Climbup Insect Interceptors

Directions for Use

4. Re-lubricating Climbup® Insect Interceptors
If the talc film is rubbed off or the device has been emptied and cleaned,
device does not need to be re-lubricated to function with daily
monitoring/bed bug removal.. However, talc film absorbs bed bug
secretions and excretions which will permit continued bed bug capture
in neglected device over months.
5. Discarding Climbup® Insect Interceptors After Installation
Care should be exercised when discarding Climbup® devices to avoid
contact with live bugs that are on, in or around the devices.
When discarding devices be sure to:
 Prior to removing the devices you should have plastic bags available
 Remove Climbup® carefully from beneath the legs of the furniture
 Wash device in soapy water to remove all bugs. The soapy water can
Climbup® is a trademark of Susan McKnight, Inc.
Susan McKnight, Inc.
2924 Walnut Grove Road
Memphis, TN 38111 USA
EPA EST. NO. 85542-TN-001
www.insect-interceptor.com
FIG. 1. Climbup® Insect Interceptor
Center well
Outer pitfall
The manufacturer of the Clmbup®insect interceptor is not
responsible for any injury, disease or illness caused, or allegedly
caused by bites, stings or contamination of bed bugs or any other
insects.
to place the traps in after removing them from beneath the legs of the
furniture. It is important that the bags do not have any rips, tears or
holes. You should have the bags with you so the devices can be
immediately placed in the bags once they are removed from under the
legs of the furniture.
and immediately place into a sealed plastic bag.
be dumped into a toilet and flushed. The Climbup® devices are made
of recyclable plastic and once cleaned can be disposed of in a
recycling bin that accepts high density polyethylene (HDPE= #2
recycling symbol). If device is not washed, discard in sealed plastic
bag in outdoor receptacle.