MOUNTING YOUR SENSORS ..........................18 ACCESSING THE DASHBOARD .......................... 19 SETTING UP AN E-MAIL ACCOUNT ........................20 SETTING UP YOUR DROPBOX FOR LOGGING....................22 APPENDIX A. CARRIER TEXT MESSAGING URL ADDRESSES ..............25 Node-RED™ SOFTWARE LICENSE ........................27 ADVANTECH TECHNICAL SUPPORT ......................... 28...
REFRIGERATION MONITORING KIT REFRIGERATION MONITORING STARTER KIT Kit Model BB-WSK-REF-2 The Wzzard™ Mesh Refrigeration Monitoring Application Kit provides a non-intrusive, easily installed solution for monitoring internal and external temperature, door open/closed and current draw on refrigeration equipment without disrupting your existing facility operations. Email or text message alerts can be sent when user-configured high or low limits are exceeded in critical applications.
REFRIGERATION MONITORING KIT DOWNLOADING REFRIGERATION MONITOR NODE-RED™ FLOW TO THE GATEWAY NOTE: The gateway must be in operational and online state in order to add the HVAC application (ie Eth1 must be plugged in). 1. Follow the instructions in the Gateway’s Quick Start Guide to claim your gateway. 2.
Page 7
REFRIGERATION MONITORING KIT 5. Check the box next to REF. A list of components to be updated will appear.
Page 8
REFRIGERATION MONITORING KIT 6. Click OK to accept the download.
Page 9
REFRIGERATION MONITORING KIT 7. Click Add/Upgrade Selected to start the download.
Page 10
REFRIGERATION MONITORING KIT 8. The download could take several minutes. To monitor the progress, select History from the Manage Device screen.
Page 11
REFRIGERATION MONITORING KIT 9. As each component is updated, it will be indicated with a check mark: NOTE: “AddNode” commands will show an X if they have already been installed. Note: If, for some reason all or a portion of the installation fails, repeat the procedure to install the rest of the package.
REFRIGERATION MONITORING KIT WAKE UP WZZARD™ MESH EDGE NODE 1. Press and hold the Config/Status button for 5 seconds until the Status LED starts blinking. 2. Check LED. 3. After you have awakened the node, the LED will begin to blink. This indicates that the node is attempting to establish a network connection.
REFRIGERATION MONITORING KIT ACCESS Node-RED™ UI IN THE GATEWAY 1. Attach the antenna to the Wzzard™ Mesh antenna port on the gateway. 2. Attach the Ethernet cable to the ETH0 port on the gateway and the other end to your PC. You will use an Ethernet connection to configure the gateway and to communicate with it.
REFRIGERATION MONITORING KIT NETWORK HEALTH PAGE 1. Click the Network Health button on the lower left corner of the Configuration page (see previous screen). The page below appears. This page shows the status of the network.
REFRIGERATION MONITORING KIT ATTACHING THE SENSORS ON THE INTELLIGENT EDGE NODES The Wzzard™ Mesh Refrigeration Monitoring Kit comes with built-in sensors for ambient temperature and humidity, along with two AC current sensors, a door switch, and a breakout cable with 10K thermistor. 1.
REFRIGERATION MONITORING KIT MOUNTING YOUR SENSORS Current Sensors The sensor can be mounted in any position. 1. Open the clamp release by pushing it away from the sensor body. Run the wire you are monitoring through the opening in the sensor. 2.
REFRIGERATION MONITORING KIT ACCESSING THE DASHBOARD 1. Open a browser on your computer and open the Node-RED™ Configuration page. The default address is: 192.168.1.1:1880/ui 2. Click on the Dashboard button on the lower left corner of the configuration page. 3. The dashboard should look like the following screen. 4.
REFRIGERATION MONITORING KIT SETTING UP AN E-MAIL ACCOUNT 1. From your browser, open the Node-RED™ flow at 192.168.1.1:1880. 2. Enter your user name and password. Default is: Username: NodeRED Password: 5mart5warm (set same as the SmartSwarm 342 password). 3. Find the green Send Email node on the right; double click on it.
Page 21
REFRIGERATION MONITORING KIT REF_342 3. Enter your UserID and Password for your e-mail server in the appropriate boxes. (Leave the “To” field blank.) NOTE: If you are using a G-Mail account, you will need to enable “Less Secure Apps” in the Google security settings.
REFRIGERATION MONITORING KIT SETTING UP YOUR DROPBOX FOR LOGGING 1. Log in to your Dropbox account or sign up for a new one. 2. Once signed up or logged in: • Go to https://www.dropbox.com/developers • Click Create Your App box in the center of the screen. •...
Page 23
REFRIGERATION MONITORING KIT REF_342 5. Then click on the pencil icon next to the Dropbox text window. REF_342 6. Fill in the Access Token that you got from Dropbox. (See yellow box for more information.)
Page 24
REFRIGERATION MONITORING KIT 7. Click Update; then Done again to close both windows. 8. Click the Deploy button in the upper right corner of the page. NOTE: Once you deploy the edited flow, you will have to re-enter any alert settings on the Configuration screen of the Dashboard.
REFRIGERATION MONITORING KIT Node-RED™ SOFTWARE LICENSE Copyright (2019) (Advantech) Node-RED is licensed under the Apache License, Version 2.0 (the "License"), You may not use Node-RED software preinstalled in the SmartSwarm Gateway except in compli- ance with the License. You may obtain a copy of the License at: http://www.apache.org/licenses/LICENSE-2.0...