Protekt AT 183 Instruction Manual

there are many hazards that may affect the performance of the equipment and corresponding safety precautions that have to be observed
during equipment utilization, especially:
- trailing or looping of cable or lifelines over sharp edges,
- any defects like cutting, abrasion, corrosion,
- climatic exposure,
- pendulum falls,
- extremes of temperature,
- chemical reagents,
- electrical conductivity.
personal protective equipment must be transported in the package (e.g.: bag made of moisture-proof textile or foil bag or cases made of
steel or plastic) to protect it against damage or moisture.
the equipment can be cleaned without causing adverse effect on the materials in the manufacture of the equipment. For textile products use
mild detergents for delicate fabrics, wash by hand or in a machine and rinse in water. Plastic parts can be cleaned only with water. When the
equipment becomes wet, either from being in use or when due cleaning, it shall be allowed to dry naturally, and shall be kept away from direct
heat. In metallic products some mechanic parts (spring, pin, hinge, etc.) can be regularly slightly lubricated to ensure better operation.
Other maintenance and cleaning procedures should be adhered to detailed instructions stated in the manual of the equipment.
personal protective equipment should be stored loosely packed, in a well-ventilated place, protected from direct light, ultraviolet degradation,
damp environment, sharp edges, extreme temperatures and corrosive or aggressive substances.
IT IS THE RESPONSIBILITY OF THE USER ORGANISATION TO PROVIDE THE IDENTITY CARD AND TO FILL IN THE DETAILS REQUIRED.
THE IDENTITY CARD SHOULD BE FILLED IN BEFORE THE FIRST USE BY A COMPETENT PERSON, RESPONSIBLE INTHE USER ORGANIZATION FOR PROTECTIVE EQUIPMENT.
ANY INFORMATION ABOUT THE EQUIPMENT LIKE PERIODIC INSPECTIONS, REPAIRS, REASONS OF EQUIPMENT'S WITHDRAWN FROM USE SHALL BE NOTED INTO THE IDENTITY CARD BY A COMPETENT PERSON.
THE IDENTITY CARD SHOULD BE STORAGED DURING A WHOLE PERIOD OF EQUIPMENT UTILIZATION.
DO NOT USE THE EQUIPMENT WITHOUT THE IDENTITY CARD.
ALL RECORDS IN THE IDENTITY CARD CAN BE FILLED IN ONLY BY A COMPETENT PERSON.

IDENTITY CARD

MODEL AND TYPE OF EQUIPMENT
REF. NUMBER
SERIAL NUMBER
USER NAME
DATE OF PURCHASE
PERIODIC EXAMINATION AND REPAIR HISTORY
REASON FOR
DATE
ENTRY PERIODIC EXAMINATION
OR REPAIR AND OTHER REVELANT INFORMATIONS
1
2
3
4
PROTEKT, 93-403 LODZ,
ul. Starorudzka 9, POLAND,
TEL: (48 42) 680 20 83, FAX: (48 42) 680 20 93
www.protekt.com.pl
DATE OF MANUF.
DATE OF PUTTING
INTO OPERATION
DEFECTS NOTED, NAME AND SIGNATURE
REPAIRS CARRIED OUT OF COMPETENT PERSON
Notified body which supervises
the production of the equipment:
APAVE SUDEUROPE SAS - CS60193 - 13322 MARSEILLE CEDEX 16 - FRANCE
Instructi o n Manual
EN 795:2012
Ref.: AT183
APAVE SUDEUROPE SAS - CS60193 - 13322 MARSEILLE CEDEX 16 - FRANCE
Anchor device AT183 is a component of personal protective equipment against falls from a height. It is used to connect fall arrest
devices to the structural anchor point. Anchor device AT183 conforms the standard EN 795 type A - protection against falls from a
height - Anchor devices.
Anchor device AT183 is appropriate for a single person use only.

CONSTRUCTION

Static strength -min.12kN
Material: Stainless steel ANSI304
Number of person: 1
Anchor point
PERIODIC
EXAMINATION
NEXT DUE DATE
According to European standard EN 365:2004 and EN 795:2012 + A1:2000Type A a requirement to check the legibility of the product markings
PROTEKT 93-403 £ÓDZ ul. Starorudzka 9 POLAND
Notified body, which supervises the production of the equipment:
Fig.1. Dimensions of the device AT183
ANCHOR
P O I N T
A T 1 8 3
T y p e A
Bearing element
TEL/FAX: (0 42) 683 03 21; 683 03 22
1